- 您现在的位置：买卖IC网 > PDF目录20711 > MAX6974ATL+T (Maxim Integrated)IC LED DRIVER LINEAR 40-TQFN PDF资料下载
参数资料
| 型号： | MAX6974ATL+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 20/23页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | PWM |
| 输出数： | 24 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 类型 - 次要： | RGB |
| 频率： | 33MHz |
| 电源电压： | 3 V ~ 3.6 V |
| 输出电压： | 7V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
24-Output PWM LED Drivers
for Message Boards
When the MAX6974/MAX6975 send individual-intensity
PWM data, the data segment bit length is large due to
the 12-bit or 14-bit PWM data for each of the 24 outputs
(see Figure 11). The various data segment bit lengths
for each of the four commands and different operating
modes is shown in Table 4. Data capturing is the same
as described above with the header segment outputs
and data being delayed by the full length of the data bit
stream being captured plus one clock cycle.
header and new counter value out DOUT. Regardless
of the number of open-circuit outputs on a device, the
counter increment is 1.
The MAX6974/MAX6975 detect die temperatures above
T DIE = +165°C and disable all output drivers by setting
all PWM data to zero. During an overtemperature event,
the MAX6974/MAX6975 increment the counter segment
data, CNTR[9:0], received on DIN by 1 before transmitting
a header and new counter value out DOUT. The output
D0
H1 DATA 1 PWM 288 BITS
DATA 2 PWM 288 BITS DATA 3 PWM 288 BITS T
drivers are allowed to be on when the die temperature
falls below T DIE = +150°C.
D1
289 CLOCKS
H2 DATA 2 PWM 288 BITS DATA 3 PWM 288 BITS T
When there is no fault detected, the counter data is
D2
289 CLOCKS
H3 DATA 3 PWM 288 BITS T
passed directly to DOUT unaltered.
D3
289 CLOCKS
H4 T
Applications Information
Terminations and PCB Layout
Figure 11. Long (288 Bits) PWM Data Cascading Shown for
MAX6974 in Nonmultiplexed Mode
LED Open-Circuit and
Overtemperature Detection Counter
The MAX6974/MAX6975 feature LED open-circuit
detection and overtemperature detection that use the
counter section of the header segment to record
detected faults. Using commands 01 or 11 force the
counter to record LED open-circuit detection faults.
Using commands 00 or 10 force the counter to record
overtemperature faults.
The MAX6974/MAX6975 detect an open circuit on a driver
output by monitoring for output voltages below 200mV.
When an open circuit is detected, the MAX6974/
MAX6975 increment the counter segment data,
CNTR[9:0], received on DIN by 1 before transmitting a
The MAX6974/MAX6975’s layout simplifies cascading
multiple devices, as the interface signals flow through
from each device. The synchronous and buffered
nature of the interface simplifies the board design, but
pay attention to signal routing and termination, as with
other high-speed logic circuits.
Terminate the differential input pairs, CLKI+ and CLKI-,
as well as DIN+ and DIN-, with a termination resistor as
close as possible to the package. When using the
MAX6974/MAX6975 as the signal source, use a 200 Ω
termination resistor. When using a level translator or clock
retimer as the signal source, use a 110 Ω termination
resistor. Route each differential input pair as close
parallel tracks with spacing or a GND trace between
the track pair and the next signal track to minimize
cross-coupling. Track lengths up to a few inches do not
require termination-matched tracks (transmission lines).
n MORE DEVICES WITH
200 Ω TERMINATION
LOAD
LOADI
LOADO
LOADI
LOADO
DIN
DIN1
DO1+
DIN+
DOUT+
DIN+
DOUT+
HOST
110 Ω
200 Ω
MAX9112
MAX6974
MAX6974
CLK
DIN2
DO1-
DO2+
DIN-
CLKI+
DOUT-
CLKO+
DIN-
CLKI+
DOUT-
CLKO+
110 Ω
200 Ω
DO2-
CLKI-
CLKO-
CLKI-
CLKO-
Figure 12. Typical Cascaded Serial-Interface Termination Circuit
n-1
n-2
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| TPME686K025H0055 | CAP TANT 68UF 25V 10% 2917 |
| AISC-0603-R0082J-T | INDUCTOR WW CERAM 8.2NH 0603 |
| HMM43DSEN-S243 | CONN EDGECARD 86POS .156 EYELET |
| MAX8882EUT55+T | IC REG LDO 1.8V .16A SOT23-6 |
| MPG06M-E3/54 | DIODE 1A 1000V MINI MPG06 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6974EVKIT | 功能描述:LED 照明开发工具 MAX6974 Evaluation Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX6974EVKIT+ | 功能描述:LED 照明开发工具 MAX6974 Evaluation Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX6975ATL | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6975ATL+ | 功能描述:LED照明驱动器 24-Output PWM LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX6975ATL+T | 功能描述:LED照明驱动器 24-Output PWM LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。