- 您现在的位置：买卖IC网 > PDF目录3772 > MAX7320ATE+ (Maxim Integrated Products)IC I/O EXPANDER I2C 8B 16TQFN-EP PDF资料下载
参数资料
| 型号： | MAX7320ATE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 接口： | I²C |
| 输入/输出数： | 8 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 1.71 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（3x3） |
| 包装： | 管件 |
| 包括： | POR |
Acknowledge
The acknowledge bit is a clocked 9th bit the recipient
uses to acknowledge receipt of each byte of data
(Figure 4). Each byte transferred effectively requires 9
bits. The master generates the ninth clock pulse, and
the recipient pulls down SDA during the acknowledge
clock pulse, such that the SDA line is stable low during
the high period of the clock pulse. When the master is
transmitting to the MAX7320, the device generates the
acknowledge bit because the MAX7320 is the recipi-
ent. When the MAX7320 is transmitting to the master,
the master generates the acknowledge bit because the
master is the recipient.
Slave Address
The MAX7320 has a 7-bit slave address (Figure 5). The
8th bit following the 7-bit slave address is the R/W bit. It is
low for a write command, and high for a read command.
The 1st (A6), 2nd (A5), and 3rd (A4) bits of the
MAX7320 slave address are always 1, 0, and 1.
Connect AD0 and AD2 to GND, V+, SDA, or SCL to
select the slave address bits A3, A2, A1, and A0. The
MAX7320 has 16 possible slave addresses (Table 3),
allowing up to 16 MAX7320 devices on an I2C bus.
Note the MAX7320 offers a different range of I2C slave
addresses from the MAX7319, MAX7321, MAX7322 and
MAX7323, for which 1st (A6), 2nd (A5), and 3rd (A4)
bits of the slave address are always 1, 1, and 0.
Accessing the MAX7320
A single-byte read from the MAX7320 returns the sta-
tus of the eight output ports, read back as inputs.
A 2-byte read repeatedly returns the status of the eight
output ports, read back as inputs.
A multibyte read (more than 2 bytes before the I2C
STOP bit) repeatedly returns the status of the eight out-
put ports, read back as inputs.
A single-byte write to the MAX7320 sets the logic state
of all eight outputs.
A multibyte write to the MAX7320 repeatedly sets the
logic state of all eight outputs.
Reading from the MAX7320
A read from the MAX7320 starts with the master trans-
mitting the MAX7320’s slave address with the R/W bit
set high. The MAX7320 acknowledges the slave
address, and samples the logic state of the output
ports during the acknowledge bit. The master can read
one or more bytes from the MAX7320 and then issue a
STOP condition (Figure 6). The MAX7320 transmits the
current port data, read back from the actual port out-
puts (not the port output latches) during the acknowl-
edge. If a port is forced to a logic state other than its
programmed state, the read back reflects this. If driving
a capacitive load, readback port level verification algo-
rithms may need to take the RC rise/fall time into
account.
Typically, the master reads one byte from the MAX7320,
then issues a STOP condition (Figure 6). However, the
master can read 2 or more bytes from the MAX7320,
then issue a STOP condition. In this case, the MAX7320
resamples the port outputs during each acknowledge
and transmits the new data each time.
Writing to the MAX7320
A write to the MAX7320 starts with the master transmit-
ting the MAX7320’s slave address with the R/W bit set
low. The MAX7320 acknowledges the slave address
and samples the ports during the acknowledge bit. The
master can transmit one or more bytes of data. The
MAX7320 acknowledges each subsequent byte of data
and updates the output ports until the master issues a
STOP condition (Figure 7).
MAX7320
I2C Port Expander with Eight Push-Pull Outputs
_______________________________________________________________________________________
9
SDA
SCL
DATA LINE STABLE;
DATA VALID
CHANGE OF DATA
ALLOWED
Figure 3. Bit Transfer
SCL
SDA BY
TRANSMITTER
CLOCK PULSE
FOR ACKNOWLEDGMENT
START
CONDITION
SDA BY
RECEIVER
12
89
S
Figure 4. Acknowledge
相关PDF资料 |
PDF描述 |
|---|---|
| DS4520E+ | IC I/O EXPANDER I2C 9B 16TSSOP |
| MAX7315AEE+ | IC I/O EXPANDER I2C 8B 16QSOP |
| MAX7315AUE+ | IC I/O EXPANDER I2C 8B 16TSSOP |
| MCP23S08T-E/SO | IC I/O EXPANDER SPI 8B 18SOIC |
| 346-220-058 | CARD GUIDE OFFSET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7320ATE+ | 功能描述:接口-I/O扩展器 I2C Port Expander w/8 Push-Pull Out RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7320ATE+T | 功能描述:接口-I/O扩展器 I2C Port Expander w/8 Push-Pull Out RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7320ATE-T | 功能描述:接口-I/O扩展器 RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7320EVKIT+ | 功能描述:界面开发工具 Evaluation Kit for the MAX7320 RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX7321 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C Port Expander with 4 Push-Pull Outputs |
发布紧急采购，3分钟左右您将得到回复。