- 您现在的位置：买卖IC网 > PDF目录11137 > MAX7357ETG+T (Maxim Integrated Products)IC MULTIPLEXER 8X1 24TQFN PDF资料下载
参数资料
| 型号： | MAX7357ETG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/22页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLEXER 8X1 24TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 多路复用器 |
| 电路： | 1 x 8:1 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
MAX7356/MAX7357/MAX7358
1-to-8 I2C Bus Switches/Multiplexers with Bus
Lock-Up Detection, Isolation, and Notification
______________________________________________________________________________________
13
Only the switch control register can be accessed through
an I2C write or read command. All data bytes are for
the switch control register. The last data byte in an I2C
write command is retained by the switch control register.
Register Access Protocol
(MAX7357/MAX7358)
Only the MAX7357 or MAX7358 I2C device address is
required to gain access to its registers. A typical I2C
command to communicate with the MAX7357 or
MAX7358 starts with its device address and is followed
directly by data bytes. Internal register addresses are
not used in an I2C write or read command.
For enhanced mode, all registers are accessed in
sequence starting with the switch control register and
follows the order defined by internal register addresses
as shown in Table 2. Internal register addresses are
0x00, 0x01, 0x02, 0x03, 0x04, 0x05, and 0x06 for
switch control, configuration, flush-out sequence, lock-
up indication, first and second bytes of the traffic prior
to lock-up, and preconnection fault registers, respec-
tively. When writing data to the register(s), addressing
starts with address 0x00 and goes one higher in each
subsequent byte and comes back to 0x00 again after
0x02 since the next four higher addressed registers are
read only. Read access also starts with the internal reg-
ister address 0x00 and goes one higher in each subse-
quent byte and comes back to 0x00 again after 0x06.
For basic mode, only the switch control register can be
accessed through an I2C write or read command. All
data bytes are for the switch control register. The last
data byte in an I2C write command is retained by the
switch control register. Incomplete bytes are ignored.
Switch Control Register
The switch control register (Figure 8) selects which
channels will be connected to the main I2C bus. This
register can be written and read through the main I2C
bus. The POR value for the switch control register is
0x00—all switches disconnected.
A SC_/SD_ downstream pair, or channel, is selected by
the contents of the switch control register. All bits of the
control byte are used to determine which channel is to
B6
B0
B7
B5
B4
B3
B2
B1
CHANNEL SELECTION BITS (READ/WRITE)
CHANNEL 0
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
CHANNEL 5
CHANNEL 6
CHANNEL 7
Figure 8. Switch Control Register
B7
B6
B5
B4
B3
B2
B1
B0
COMMAND
X
XXXX
0
Channel 0 disabled
X
XXXX
1
Channel 0 enabled
X
0
X
Channel 1 disabled
X
1
X
Channel 1 enabled
X
0
X
Channel 2 disabled
X
1
X
Channel 2 enabled
X
0
X
Channel 3 disabled
X
1
X
Channel 3 enabled
X
0
X
Channel 4 disabled
X
1
X
Channel 4 enabled
X
0
XXXX
X
Channel 5 disabled
X
1
XXXX
X
Channel 5 enabled
X
0
X
XXXX
X
Channel 6 disabled
X
1
X
XXXX
X
Channel 6 enabled
0
X
XXXX
X
Channel 7 disabled
1
X
XXXX
X
Channel 7 enabled
Table 4. Switch Control Register Channel Selection
X = Don’t care.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7357EUG+T | IC MULTIPLEXER 8X1 24TSSOP |
| VI-BWY-IW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| MAX4527CSA+T | IC SWITCH DUAL SPDT 8SOIC |
| VE-J6D-IW-F2 | CONVERTER MOD DC/DC 85V 100W |
| VI-BWX-IY-F3 | CONVERTER MOD DC/DC 5.2V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7357EUG+ | 功能描述:多路器开关 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX7357EUG+T | 功能描述:多路器开关 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX7358ETG+ | 功能描述:多路器开关 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX7358ETG+T | 功能描述:多路器开关 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX7358EUG+ | 功能描述:多路器开关 IC 1-to-8 I2C Bus Switch/MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。