- 您现在的位置：买卖IC网 > PDF目录11669 > MAX7360ETL+ (Maxim Integrated Products)IC CTRLR KEY-SW I2C 40TQFN-EP PDF资料下载
参数资料
| 型号： | MAX7360ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR KEY-SW I2C 40TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 控制器 |
| 输入类型： | 逻辑 |
| 输出类型： | 逻辑 |
| 接口： | I²C，2 线串口 |
| 电流 - 电源： | 50µA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
15
Maxim Integrated
I2C-Interfaced Key-Switch Controller and LED
Driver/GPIOs with Integrated ESD Protection
MAX7360
Figure 5. Acknowledge
Figure 6. Slave Address
Slave Addresses
The MAX7360 has a 7-bit long slave address (Figure
6). The bit following a 7-bit slave address is the R/W bit,
which is low for a write command and high for a read
command.
The first 4 bits (MSBs) of the MAX7360 slave address
are always 0111. Slave address bits A3, A2, and A1
correspond, by the matrix in Table 3, to the states of the
device address input AD0, and A0 corresponds to the
R/W bit. The AD0 input can be connected to any of four
signals (GND, VCC, SDA, or SCL), giving four possible
slave address pairs and allowing up to four MAX7360
devices to share the bus. Because SDA and SCL are
dynamic signals, care must be taken to ensure that AD0
transitions no sooner than the signals on SDA and SCL.
The MAX7360 monitors the bus continuously, waiting for a
START condition, followed by its slave address. When the
MAX7360 recognizes its slave address, it acknowledges
and is then ready for continued communication.
Bus Timeout
The MAX7360 features a 20ms minimum bus timeout
on the 2-wire serial interface, largely to prevent the
MAX7360 from holding the SDA I/O low during a read
transaction should the SCL lock up for any reason before
a serial transaction is completed. Bus timeout operates
by causing the MAX7360 to internally terminate a serial
Figure 7. Command Byte Received
Figure 8. Command and Single Data Byte Received
SCL
SDA
BY
TRANSMITTER
CLOCK PULSE FOR
ACKNOWLEDGE
START
CONDITION
SDA
BY
RECEIVER
1
2
8
9
S
SDA
SCL
0
1
A3
A2
A1
1
MSB
LSB
ACK
R/W
S
A
P
0
SLAVE ADDRESS
COMMAND BYTE
D7
D6
D5
D4
D3
D2
D1
D0
COMMAND BYTE IS STORED ON RECEIPT OF
ACKNOWLEDGE CONDITION
ACKNOWLEDGE FROM MAX7360
R/W
S
A
P
0
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
1 BYTE
AUTOINCREMENT
COMMAND BYTE ADDRESS
D7
D6
D5
D4
D3
D2
D1
D0
D1
D0
D3
D2
D5
D4
D7
D6
ACKNOWLEDGE FROM MAX7360
R/W
相关PDF资料 |
PDF描述 |
|---|---|
| DS1878T+ | IC CTLR SFP W/DGTL LDD RX 28TQFN |
| MAX9621AUB+ | IC HALL EFFECT SENSOR 10UMAX |
| VI-J40-IW-F1 | CONVERTER MOD DC/DC 5V 100W |
| AD2S82ALPZ | IC CONV R/D MONO VAR RES 44PLCC |
| VI-J40-IW-F2 | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7360ETL+ | 功能描述:外围驱动器与原件 - PCI Key-Switch Ctlr & LED Driver/GPIO RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7360ETL+T | 功能描述:外围驱动器与原件 - PCI Key-Switch Ctlr & LED Driver/GPIO RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7360EVKIT+ | 制造商:Maxim Integrated Products 功能描述:I2C-INTERFACED KEY-SWITCH CONTROLLE - Boxed Product (Development Kits) |
| MAX7360EWX+ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C-Interfaced Key-Switch Controller and LED Driver/GPIOs with Integrated ESD Protection |
| MAX7360EWX+T | 功能描述:外围驱动器与原件 - PCI Key-Switch Ctlr & LED Driver/GPIO RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。