- 您现在的位置：买卖IC网 > PDF目录15038 > MAX742CWP+T (Maxim Integrated Products)IC REG CTRLR BST INV PWM 20-SOIC PDF资料下载
参数资料
| 型号： | MAX742CWP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST INV PWM 20-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 200kHz |
| 占空比： | 90% |
| 电源电压： | 4.2 V ~ 10 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
Switch-Mode Regulator with
+5V to ±12V or ±15V Dual Output
Supply-Voltage Range
Although designed for operation from a +5V logic
supply, the MAX742 works well from 4.2V (the upper
limit of the undervoltage lockout threshold) to +10V
(absolute maximum rating plus a safety margin). The
+5V
5 μ A
MAX742
upper limit can be further increased by limiting the
voltage at V+ with a zener shunt or series regulator.
To ensure AC stability, the inductor value should be
8 SS
+2V
REFERENCE
scaled linearly with the nominal input voltage. For
example, if Figure 3’s application circuit is powered
from a nominal 9V source, the inductor value should be
increased to 40μH or 50μH. At high input voltages
(>8V), the charge pump can cause overvoltage at
EXTERNAL
SS
CAPACITOR
N
TO CURRENT–
LIMIT COMPARATOR
FAULT
PDRV. If the input can exceed 8V, ground PDRV and
remove the capacitors and diodes associated with the
charge pump.
In-Circuit Testing for
Guaranteed Performance
Figure 2’s circuit has been tested at all extremes of line,
load, and temperature. Refer to the Electrical
Characteristics table for guaranteed in-circuit specifica-
tions. Successful use of this circuit requires no compo-
nent calculations.
Soft-Start
A capacitor connected between Soft-Start (SS) and
ground limits surge currents at power-up. As shown in
the Typical Operating Characteristics, the peak switch
current limit is a function of the voltage at SS. SS is
internally connected to a 5μA current source and is
diode-clamped to 2.6V (Figure 8). Soft-start timing is
therefore set by the SS capacitor value. As the SS volt-
age ramps up, peak inductor currents rise until they
reach normal operating levels. Typical values for the SS
capacitor, when it is required at all, are in the range of
1μF to 10μF.
Fault Conditions Enabling SS Reset
In addition to power-up, the soft-start function is enabled
by a variety of fault conditions. Any of the following con-
ditions will cause an internal pull-down transistor to dis-
charge the SS capacitor, triggering a soft-start cycle:
Undervoltage lockout
Thermal shutdown
VREF shorted to ground or supply
VREF losing regulation
Figure 4. Soft-Start Equivalent Circuit
__________________Design Procedure
Inductor Value
An exact inductor value isn’t critical. The inductor value
can be varied in order to make tradeoffs between
noise, efficiency, and component sizes. Higher inductor
values result in continuous-conduction operation, which
maximizes efficiency and minimizes noise. Physically
smallest inductors (where E = 1/2 LI 2 is minimum) are
realized when operating at the crossover point between
continuous and discontinuous modes. Lowering the
inductor value further still results in discontinuous cur-
rent even at full load, which minimizes the output
capacitor size required for AC stability by eliminating
the right-half-plane zero found in boost and inverting
topologies. Ideal current-mode slope compensation
where m = 2 x V/L is achieved if L (Henries) = R SENSE
( ? ) x 0.001, but again the exact value isn’t critical and
the inductor value can be adjusted freely to improve
AC performance. The following equations are given for
continuous-conduction operation since the MAX742 is
mainly intended for low-noise analog power supplies.
See Appendix A in Maxim’s Battery Management and
DC-DC Converter Circuit Collection for crossover point
and discontinuous-mode equations.
Boost (positive) output:
(V IN - V SW ) 2 (V OUT + V D - V IN )
L = ———————————————
(V OUT + V D ) 2 (I LOAD )(F)(LIR)
Inverting (negative) output:
(V IN - V SW ) 2
L = —————————————
(V OUT + V D )(I LOAD )(F)(LIR)
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2TY-EY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| MAX742EWP+T | IC REG CTRLR BST INV PWM 20-SOIC |
| MAX1992ETG+ | IC REG CTRLR BUCK PWM CM 24-TQFN |
| MAX1897ETP+ | IC REG CTRLR BUCK PWM 20-TQFN |
| MAX1844ETP+ | IC REG CTRLR BUCK PWM CM 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX742EPP | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX742EPP+ | 功能描述:直流/直流开关调节器 Switch-Mode Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX742EVKIT-SO | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX742EWP | 功能描述:直流/直流开关调节器 Switch-Mode Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX742EWP/G0F | 制造商:Maxim Integrated Products 功能描述:SWITCH-MODE REGULATOR WITH 5V TO ?12 OR ?15V DUAL-OUTPUT - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。