- 您现在的位置：买卖IC网 > PDF目录13580 > MAX860IUA+T (Maxim Integrated Products)IC REG SWITCHD CAP DBL INV 8UMAX PDF资料下载
参数资料
| 型号： | MAX860IUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/11页 |
| 文件大小： | 0K |
| 描述： | IC REG SWITCHD CAP DBL INV 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 切换式电容器（充电泵），倍增器，反相 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | -1.5 V ~ -5.5 V，3 V ~ 11 V |
| 输入电压： | 1.5 V ~ 5.5 V |
| 频率 - 开关： | 6kHz，50kHz，130kHz |
| 电流 - 输出： | 50mA |
| 同步整流器： | 无 |
| 工作温度： | -25°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-uMAX |
MAX860/MAX861
50mA, Frequency-Selectable,
Switched-Capacitor Voltage Converters
_______________Detailed Description
The MAX860/MAX861 capacitive charge pumps either
invert or double the voltage applied to their inputs. For
highest performance, use low equivalent series resis-
tance (ESR) capacitors. See the Capacitor Selection
section for more details. The frequency-control (FC) pin
allows you to choose one of three switching frequen-
cies; these three selectable frequencies are different for
each device. When shut down, MAX860/MAX861 cur-
rent consumption reduces to less than 1μA.
Common Applications
Voltage Inverter
The most common application for these devices is a
charge-pump voltage inverter (see Typical Operating
Circuits). This application requires only two external com-
ponents—capacitors C1 and C2—plus a bypass capacitor
if necessary (see Bypass Capacitor section). Refer to the
Capacitor Selection section for suggested capacitor types
and values.
Even though the MAX860/MAX861’s output is not actively
regulated, it is fairly insensitive to load-current changes. A
circuit output source resistance of 12 Ω (calculated using
the formula given in the Capacitor Selection section)
means that, with a +5V input, the output voltage is -5V
is not used. When the device is shut down, all active
circuitry is turned off.
In the inverting configuration, loads connected from
OUT to GND are not powered in shutdown mode.
However, a reverse-current path exists through two
diodes between OUT and GND; therefore, loads con-
nected from V DD to OUT draw current from the input
supply.
In the doubling configuration, loads connected from the
V DD pin to the GND pin are not powered in shutdown
mode. Loads connected from the V DD pin to the OUT
pin draw current from the input supply through a path
similar to that of the inverting configuration (described
above).
Frequency Control
Charge-pump frequency for both devices can be set to
one of three values. Each device has a unique set of
three available frequencies, as indicated in Table 1.
The oscillator and charge-pump frequencies are the
same (i.e., the charge-pump frequency is not half the
oscillator frequency, as it is on the MAX660, MAX665,
and ICL7660).
Table 1. Nominal Switching Frequencies*
under no load and decreases to -4.4V with a 50mA load.
The MAX860/MAX861 output source resistance (used to
calculate the circuit output source resistance) vs. tempera-
FC CONNECTION
FREQUENCY (kHz)
MAX860 MAX861
ture and supply voltage are shown in the Typical
Operating Characteristics graphs.
Calculate the output ripple voltage using the formula
given in the Capacitor Selection section.
FC = V DD or open
FC = GND
FC = OUT
6
50
130
13
100
250
Active-Low Shutdown Input
device. In inverter mode, connect S H – — — — – to V DD if it is
Positive Voltage Doubler
The MAX860/MAX861 can also operate as positive volt-
age doublers (see Typical Operating Circuits ). This
application requires only two external components,
capacitors C1 and C2. The no-load output is twice the
input voltage. The electrical specifications in the doubler
mode are very similar to those of the inverter mode
except for the Supply Voltage Range (see Electrical
Characteristics table) and No-Load Supply Current (see
graph in Typical Operating Characteristics). The circuit
output source resistance and output ripple voltage are
calculated using the formulas in the Capacitor Selection
section.
– — — — –
–— —–
When driven low, the S H D N input — shuts down the
D N
not used. In doubler mode, connect S H D N to GND if it
6
*See the Electrical Characteristics for detailed switching-
frequency specifications.
A higher switching frequency minimizes capacitor size
for the same performance and increases the supply
current (Table 2). The lowest fundamental frequency of
the switching noise is equal to the minimum specified
switching frequency (e.g., 3kHz for the MAX860 with FC
open). The spectrum of noise frequencies extends
above this value because of harmonics in the switching
waveform. To get best noise performance, choose the
device and FC connection to select a minimum switch-
ing frequency that lies above your sensitive bandwidth.
Low-Voltage-Operation Input
LV should be connected to GND for inverting operation.
To enhance compatibility with the MAX660, MAX665, and
ICL7660, you may float LV if the input voltage exceeds 3V.
In doubling mode, LV must be connected to OUT for all
input voltages.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| SCB63C-680 | INDUCTOR SMD 68UH 0.27A 1KHZ |
| 16YXG2200MEFCG412.5X20 | CAP ALUM 2200UF 16V 20% RADIAL |
| SCB63C-560 | INDUCTOR SMD 56UH 0.30A 1KHZ |
| 16YXG2200MEFC12.5X20 | CAP ALUM 2200UF 16V 20% RADIAL |
| SCB63C-4R7 | INDUCTOR SMD 4.7UH 1.15A 1KHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX860MJA | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX860MSA/PR2 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX860MSA/PR2-T | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX8610ETD+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX8610ETM+ | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。