- 您现在的位置：买卖IC网 > PDF目录1848 > MAX864EEE+T (Maxim Integrated Products)IC REG SWTCHD CAP DBL INV 16QSOP PDF资料下载
参数资料
| 型号： | MAX864EEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC REG SWTCHD CAP DBL INV 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 切换式电容器（充电泵），倍增器，反相 |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | ±3.5 V ~ ±12 V |
| 输入电压： | 1.75 V ~ 6 V |
| 频率 - 开关： | 185kHz |
| 电流 - 输出： | 35mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-QSOP |
Dual-Output Charge Pump with Shutdown
( )
( )( )
= C1 ? V +
? 2 V +
V IN ?
( )
( )
+
C 2 ? V +
? V ? ?
Charge-Pump Output
The MAX864 is not a voltage regulator: the output
source resistance of either charge pump is approxi-
mately 55 ? at room temperature (with V IN = 5V); and V+
and V- approach +10V and -10V, respectively, when
lightly loaded. Both V+ and V- will droop toward GND as
the current draw from either V+ or V- increases, since V-
is derived from V+. Treating each converter separately,
the droop of the negative supply (V DROOP- ) is the prod-
uct of the current draw from V- (I V- ) and the source
resistance of the negative converter (RS-):
V DROOP- = I V - x RS -
The droop of the positive supply (V DROOP+ ) is the
product of the current draw from the positive supply
(I LOAD+ ) and the source resistance of the positive con-
verter (RS+), where I LOAD+ is the combination of I V-
and the external load on V+ (I V+ ):
V DROOP+ = I LOAD+ x RS+ = ( I V+ + I V - ) x RS+
Determine V+ and V- as follows:
V+ = 2V IN - V DROOP+
V - = (V+ - V DROOP )
= -(2V IN -V DROOP+ -V DROOP- )
The output resistances for the positive and negative
charge pumps are tested and specified separately. The
positive charge pump is tested with V- unloaded. The
negative charge pump is tested with V+ supplied from
an external source, isolating the negative charge pump.
Current draw from either V+ or V- is supplied by the
reservoir capacitor alone during one half cycle of the
clock. Calculate the resulting ripple voltage on either
output as follows:
Shutdown
The MAX864 features a shutdown mode that reduces
the maximum supply current to 1μA over temperature.
The SHDN pin is an active-low TTL logic-level input. If
the shutdown feature is unused, connect SHDN to IN.
In shutdown mode, V+ connects to IN through a 22 ?
switch and V- connects to GND through a 6 ? switch.
_________Efficiency Considerations
Theoretically, a charge-pump voltage multiplier can
approach 100% efficiency under the following condi-
tions:
? The charge-pump switches have virtually no offset,
and extremely low on-resistance.
? The drive circuitry consumes minimal power.
? The impedances of the reservoir and pump capaci-
tors are negligible.
For the MAX864, the energy loss per clock cycle is the
sum of the energy loss in the positive and negative
converters, as follows:
LOSS CYCLE = LOSS POS + LOSS NEG
1 ? 2 ?
2 ? ?
1 ? 2 2 ?
2 ? ?
where V+ and V- are the actual measured output volt-
ages.
The average power loss is simply:
Resulting in an efficiency of:
P LOSS = LOSS CYCLE x f PUMP
V RIPPLE =
1
2
I LOAD (1 / f PUMP ) (1 / C RESERVOIR )
η = Total Output Power / ( Total Output Power ? P LOSS
)
where I LOAD is the load on either V+ or V-. For exam-
ple, with an f PUMP of 33kHz and 6.8μF reservoir capaci-
tors, the ripple is 26mV when I LOAD is 12mA.
Remember that, in most applications, the total load on
V+ is the V+ load current (I V+ ) and the current taken by
the negative charge pump (I V- ).
There will be a substantial voltage difference between
(V+ - V IN ) and V IN for the positive pump, and between
V+ and V- if the impedances of the pump capacitors
(C1 and C2) are large with respect to their respective
output loads.
Larger reservoir capacitor (C3 and C4) values will
reduce output ripple. Larger values of both pump and
reservoir capacitors will improve efficiency.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8654ETX+T | IC REG BUCK ADJ 8A 36TQFN |
| MAX8655ETN+T | IC REG BUCK ADJ 25A 56TQFN |
| MAX865EUA | IC REG SWITCHD CAP DBL INV 8UMAX |
| MAX8660ETL/V+ | IC POWER MGMT XSCALE 48WQFN |
| MAX8663ETL+ | IC POWER MANAGE 40-TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8650EEG+ | 功能描述:DC/DC 开关控制器 4.5-28V Current-Mode Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8650EEG+T | 功能描述:DC/DC 开关控制器 4.5-28V Current-Mode Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8650EEG+TW | 制造商:Maxim Integrated Products 功能描述:WAIVERED VERSION OF MAX8650EEG+T - Tape and Reel |
| MAX8650EVKIT | 功能描述:DC/DC 开关控制器 Evaluation Kit for the MAX8650 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8653ETI+ | 功能描述:直流/直流开关调节器 Dual 5A 1.5MHz Step Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。