- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8677CETG+T (Maxim Integrated Products)IC USB/AC ADP CHARGER 24-TQFN PDF资料下载
参数资料
| 型号： | MAX8677CETG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/21页 |
| 文件大小： | 0K |
| 描述： | IC USB/AC ADP CHARGER 24-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.1 V ~ 6.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
1.5A Dual-Input USB/AC Adapter Charger
and Smart Power Selector
Pin Description (continued)
PIN
6
7
8
9
10
11
12
13
14
15, 16
17, 18
19
20, 21
22
23
24
—
NAME
PEN2
PSET
VL
GND
CT
ISET
THM
USUS
TSET
USB
BAT
CHG
SYS
DOK
UOK
FLT
EP
FUNCTION
USB High/Low Control. PEN2 sets the DC or USB current limit to 100mA (PEN2 low) or 500mA (PEN2 high).
PEN2 controls both DC and USB current limits when PEN1 is low. See Table 2.
DC Input Current-Limit Set. Connect a resistor to ground to program the DC current limit to 3000/R PSET .
Logic LDO Output. VL is the output of an LDO that powers the MAX8667C internal circuitry. VL also provides
3.3V at up to 10mA to power external circuitry. Connect a 0.1μF capacitor from VL to GND.
Ground
Charge Timer Program Pin. A capacitor from CT to GND sets the fast-charge (t FSTCHG ) and prequal (t PREQUAL )
fault timers. Connect to GND to disable the timer.
Charge Current Set Input. A resistor (R ISET ) from ISET to GND programs the maximum charge current up to 1.5A.
The prequal charge current is 10% of the set maximum charge current.
Thermistor Input. Connect a negative temperature coefficient (NTC) thermistor that has good thermal contact
with the battery from THM to GND. Connect a resistor equal to the thermistor +25°C resistance from THM to VL.
Charging is suspended when the thermistor is outside the hot and cold limits. Connect THM to GND to disable
the thermistor temperature sensor.
USB Suspend Input. With PEN1 low, driving USUS high turns off both the USB and DC inputs. With PEN1 high,
driving USUS high turns off only the USB input. See Table 2.
Termination Current Set Pin. Connect to GND, leave open, or connect to VL for a 5%, 10%, or 15% (of I CHGMAX )
termination current (I TERM ) threshold.
USB Power Input. USB is capable of delivering up to 0.5A to SYS. The USB current limit is set with PEN2 and
USUS. See Table 2. Both USB pins must be connected together externally.
Battery Connection. Connect to a single-cell Li+ battery. The battery charges from SYS when a valid source is
present at DC or USB. BAT powers SYS when neither DC nor USB power is present, or when the SYS load
exceeds the input current limit. Both BAT pins must be connected together externally.
Charger Status Output. Active-low, open-drain output pulls low when the battery is in fast-charge or prequal.
Otherwise, CHG is high impedance.
System Supply Output. SYS is connected to BAT through an internal 40m Ω system load switch when DC or USB
is invalid, or when the SYS load is greater than the input current limit.
When a valid voltage is present at DC or USB, SYS is limited to 4.35V. When the system load (I SYS ) exceeds the
DC or USB current limit, SYS is regulated to 68mV below BAT, and both the USB input and the battery service SYS.
Bypass SYS to GND with a 10μF X5R or X7R ceramic capacitor. Both SYS pins must be connected together
externally.
DC Power-OK Output. Active-low, open-drain output pulls low when a valid input is detected at DC.
USB Power-OK Output. Active-low, open-drain output pulls low when a valid input is detected at USB.
Fault Output. Active-low, open-drain output pulls low when the battery timer expires before prequal or
fast-charge complete.
Exposed Paddle. Connect the exposed paddle to GND. Connecting the exposed paddle does not remove the
requirement for proper ground connections to the appropriate pins.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX867EUA+ | IC REG BOOST ADJ 2.5MA 8UMAX |
| MAX8686ETL+T | IC REG BUCK SYNC ADJ 25A 40TQFN |
| MAX8688BLETG+ | IC PWR SUPPLY CTRLR/MONTR 24TQFN |
| MAX868EUB+T | IC REG MULTI CONFIG ADJ 10UMAX |
| MAX869LEEE+T | IC SW P-CH HIGH SIDE 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8678ETE+ | 功能描述:电荷泵 White LED Charge Pump w/1.1W Aud Amp RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| MAX8678ETE+T | 功能描述:LED照明驱动器 White LED Charge Pump w/1.1W Aud Amp RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8678EVKIT+ | 功能描述:电源管理IC开发工具 MAX8678 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX867C/D | 功能描述:直流/直流开关转换器 Adjustable Output Single-Cell DC-DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX867ESA | 功能描述:直流/直流开关转换器 3.3/5/AdjV 1-Cell DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。