- 您现在的位置：买卖IC网 > PDF目录16705 > MAX8688ALETG+T (Maxim Integrated Products)IC PWR SUPPLY CTRLR/MONTR 24TQFN PDF资料下载
参数资料
| 型号： | MAX8688ALETG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/38页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY CTRLR/MONTR 24TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源控制器/监控器 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 6.7mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页
Digital Power-Supply Controller/Monitor
with PMBus Interface
TOFF_FALL (65h)
The TOFF_FALL command sets the time, in millisec-
onds, from the end of the turn-off delay time until the
output voltage is commanded to zero. Note that this
command can only be used with a device whose out-
put can sink enough current to cause the output volt-
age to decrease at a controlled rate.
When commanded to turn off immediately through the
OPERATION command, the TOFF_FALL value is
ignored. When commanded to turn off through the
OPERATION soft-off command or A3/ONOFF (when
enabled), the TOFF_FALL parameter is used. If a
TOFF_FALL parameter results in the DAC outputting an
out-of-range value (valid range 0 to 4090) immediately
during TOFF_FALL, the CML flag is set and FLT asserts
to issue a warning.
In feedback mode, this value is not used. The
MAX8688 disables ENOUT and opens the DAC switch
immediately after the TOFF_DELAY.
The 2 data bytes are in DIRECT format. Valid values are
from 0.01ms to 32.767ms.
The default TOFF_FALL value is 0.01ms. Setting any
value less than this minimum value defaults back to
0.01ms.
STATUS_BYTE (78h)
The STATUS_BYTE command returns 1 byte of informa-
tion with a summary of the most critical faults. In the
MAX8688, status information is binary. A value of 1 indi-
cates that a fault or warning has occurred and a 0 indi-
cates otherwise. Bits for unsupported features shall be
reported as 0.
Table 6. STATUS_BYTE Message Contents
The STATUS_BYTE cannot be restored by
RESTORE_DEFAULT_ALL command. The STATUS_BYTE
message content is described in Table 6.
This command is read only.
The default STATUS_BYTE value is 40h (POL is off).
READ_VOUT (8Bh)
The READ_VOUT command returns the actual mea-
sured (not commanded) output voltage across RS+
and RS-. If filter mode is enabled, the filtered value is
returned.
The 2 data bytes are in DIRECT format. Valid values are
the same as VOUT_COMMAND.
The default READ_VOUT value is 00h.
READ_IOUT (8Ch)
The READ_IOUT command returns the measured out-
put current in amperes across ISN+ and ISN-.
The 2 data bytes are in DIRECT format. Valid values are
the same as IOUT_OC_FAULT_LIMIT.
The default READ_IOUT value is 00h.
READ_TEMPERATURE_1 (8Dh)
The MAX8688 supports only one temperature reading,
READ_TEMPERATURE_1. The MAX8688 returns the
actual on-chip measured temperature in degrees
Celsius.
The 2 data bytes are in DIRECT format. Valid values are
the same as OT_FAULT_LIMIT.
The default READ_TEMPERATURE_1 value is 00h.
BIT NUMBER
7
6
5
4
3
2
1
0
STATUS BIT NAME
BUSY
OFF
VOUT_OV
IOUT_OC
VIN_UV
TEMPERATURE
CML
OTHER
MEANING
A fault was declared because the device was busy and unable to respond.
(The MAX8688 does not support the BUSY bit. This bit always returns 0).
This bit is asserted if ENOUT is presently disabling the POL, regardless of the reason,
including simply not being enabled.
An output overvoltage fault has occurred.
An output overcurrent fault has occurred.
An input undervoltage fault has occurred.
(The MAX8688 does not support the VIN_UV bit. This bit always returns 0).
A temperature fault or warning has occurred.
A communication, memory, or logic fault has occurred.
A fault or warning not listed in bits [7:1] has occurred. See the MFR_FAULT_STATUS
(D8h) section for more information.
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ELL-4GM270M | CHOKE COIL 27UH 330MA SMD |
| RCM22DCWN | CONN EDGECARD 44POS DIP .156 SLD |
| ECC18DRYH | CONN EDGECARD 36POS DIP .100 SLD |
| ELL-4GM180M | CHOKE COIL 18UH 400MA SMD |
| V72B5E150BF2 | CONVERTER MOD DC/DC 5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8688BHETG+ | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688BHETG+T | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688BLETG+ | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688BLETG+T | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688EVKIT+ | 功能描述:电流和电力监控器、调节器 DIGITAL POWER SUPPLY RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。