- 您现在的位置：买卖IC网 > PDF目录5151 > MAX8727ETB+T (Maxim Integrated Products)IC DC/DC CONV TFT-LCD 10-TDFN PDF资料下载
参数资料
| 型号： | MAX8727ETB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC DC/DC CONV TFT-LCD 10-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 2.6 V ~ 5.5 V |
| 输出数： | 1 |
| 输出电压： | 2.6 V ~ 24 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
TFT-LCD Step-Up DC-DC Converter
Input Capacitor Selection
The input capacitor (C IN ) reduces the current peaks
drawn from the input supply and reduces noise injection
sen to cancel the zero introduced by output-capaci-
tance ESR. For optimal performance, choose the com-
ponents using the following equations:
into the IC. A 10μF ceramic capacitor is used in the typi-
cal operating circuit (Figure 1) because of the high
source impedance seen in typical lab setups. Actual
applications usually have much lower source imped-
ance since the step-up regulator often runs directly from
the output of another regulated supply. Typically, C IN
can be reduced below the values used in the typical
operating circuit. Ensure a low noise supply at IN by
R COMP ≈
C COMP ≈
315 × V IN × V OUT × C OUT
L × I MAIN ( MAX )
V OUT × C OUT
10 × I MAIN ( MAX ) × R COMP
using adequate C IN . Alternatively, greater voltage varia-
tion can be tolerated on C IN if IN is decoupled from C IN
using an RC lowpass filter (see R3 and C3 in Figure 1).
C COMP 2 ≈
0 . 0036 × R ESR × L × I MAIN ( MAX )
V IN × V OUT
?
?
?? V × I INRUSH ? I OUT × V OUT ??
R 1 = R 2 × ? MAIN ? 1 ?
Rectifier Diode Selection
The MAX8727’s high switching frequency demands a
high-speed rectifier. Schottky diodes are recommend-
ed for most applications because of their fast recovery
time and low forward voltage. The diode should be
rated to handle the output voltage and the peak switch
current. Make sure that the diode’s peak current rating
is at least I PEAK calculated in the Inductor Selection
section and that its breakdown voltage exceeds the
output voltage.
Output Voltage Selection
The MAX8727 operates with an adjustable output from
V IN to 24V. Connect a resistive voltage-divider from the
output (V MAIN ) to GND with the center tap connected to
FB (see Figure 1). Select R2 in the 10k Ω to 50k Ω range.
Calculate R1 with the following equation:
? V ?
? V FB ?
where V FB , the step-up regulator’s feedback set point,
is 1.24V (typ). Place R1 and R2 close to the IC.
Loop Compensation
The voltage feedback loop needs proper compensation
to prevent excessive output ripple and poor efficiency
caused by instability. This is done by connecting a
resistor (R COMP ) and capacitor (C COMP ) in series from
COMP to GND, and another capacitor (C COMP2 ) from
COMP to GND. R COMP is chosen to set the high-fre-
quency integrator gain for fast transient response, while
C COMP is chosen to set the integrator zero to maintain
loop stability. The second capacitor, C COMP2 , is cho-
For the ceramic output capacitor, where ESR is small,
C COMP2 is optional. The best gauge of correct loop
compensation is by inspecting the transient response
of the MAX8727. Adjust R COMP and C COMP as neces-
sary to obtain optimal transient performance.
Soft-Start Capacitor
The soft-start capacitor should be large enough that it
does not reach final value before the output has
reached regulation. Calculate C SS to be:
C SS > 21 × 10 ? 6 × C OUT ×
? 2 ?
V OUT ? V IN × V OUT
? IN ?
where C OUT is the total output capacitance including
any bypass capacitor on the output bus, V OUT is the
maximum output voltage, I INRUSH is the peak inrush
current allowed, I OUT is the maximum output current
during power-up, and V IN is the minimum input voltage.
The load must wait for the soft-start cycle to finish
before drawing a significant amount of load current.
The duration after which the load can begin to draw
maximum load current is:
t MAX = 6.77 x 10 5 x C SS
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| X40410V8-C | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
| X40410V8-BT1 | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
| HBC31DRAS-S734 | CONN EDGECARD 62POS .100 R/A PCB |
| ASC22DRYN-S13 | CONN EDGECARD 44POS .100 EXTEND |
| GMC26DRTS-S734 | CONN EDGECARD 52POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8727EUB+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX8727EVKIT | 功能描述:电源管理IC开发工具 MAX8727 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8728ETJ | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8728ETJ+ | 功能描述:直流/直流开关调节器 Power Supply for LCD/TV RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8728ETJ+T | 功能描述:LCD 驱动器 Power Supply for LCD/TV RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。