- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8730ETI+T (Maxim Integrated Products)IC CHARGER BATTERY 28-TQFN PDF资料下载
参数资料
| 型号： | MAX8730ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/29页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY 28-TQFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 8 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Low-Cost Battery Charger
CCV, CCI, CCS, and LVC Control Blocks
The MAX8730 controls input current (CCS control loop),
charge current (CCI control loop), or charge voltage
(CCV control loop), depending on the operating condi-
tion. The three control loops—CCV, CCI, and CCS—are
brought together internally at the lowest voltage clamp
(LVC) amplifier. The output of the LVC amplifier is the
feedback control signal for the DC-DC controller. The
Discontinuous Conduction
The MAX8730 operates in discontinuous conduction
mode at light loads to make sure that the inductor cur-
rent is always positive. The MAX8730 enters discontinu-
ous conduction mode when the output of the LVC
control point falls below 100mV. For RS2 = 30m ? , this
corresponds to a peak inductor current of 222mA:
minimum voltage at the CCV, CCI, or CCS appears at
the output of the LVC amplifier and clamps the other
control loops to within 0.3V above the control point.
I DIS =
1
2
×
100 mV
15 × RS 2
= 111 mA
Clamping the other two control loops close to the low-
est control loop ensures fast transition with minimal
overshoot when switching between different control
loops (see the Compensation section).
Continuous-Conduction Mode
With sufficient charge current, the MAX8730’s inductor
current never crosses zero, which is defined as contin-
uous-conduction mode. The controller starts a new
cycle by turning on the high-side MOSFET. When the
charge-current feedback signal (CSI) is greater than
the control point (LVC), the CCMP comparator output
goes high and the controller initiates the off-time by
turning off the MOSFET. The operating frequency is
governed by the off-time, which depends upon V BATT .
At the end of the fixed off-time, the controller initiates a
new cycle only if the control point (LVC) is greater than
100mV, and the peak charge current is less than the
cycle-by-cycle current limit. Restated another way,
IMIN must be high, IMAX must be low, and OVP must
be low for the controller to initiate a new cycle. If the
peak inductor current exceeds the IMAX comparator
threshold or the output voltage exceeds the OVP
threshold, then the on-time is terminated. The cycle-by-
The MAX8730 implements slope compensation in dis-
continuous mode to eliminate multipulsing. This pre-
vents audible noise and minimizes the output ripple.
Compensation
The charge-voltage and charge current-regulation
loops are compensated separately and independently
at the CCV, CCI, and CCS pins.
CCV Loop Compensation
The simplified schematic in Figure 4 is sufficient to
describe the operation of the MAX8730 when the volt-
age loop (CCV) is in control. The required compensa-
tion network is a pole-zero pair formed with C CV and
R CV . The pole is necessary to roll off the voltage loop’s
response at low frequency. The zero is necessary to
compensate the pole formed by the output capacitor
and the load. R ESR is the equivalent series resistance
(ESR) of the charger output capacitor (C OUT ). R L is the
equivalent charger output load, where R L = ? V BATT /
? I CHG . The equivalent output impedance of the GMV
cycle current limit protects against overcurrent and
short-circuit faults.
The MAX8730 computes the off-time by measuring
GM OUT
BATT
V BATT :
R ESR
R L
for V BATT > 4V.
t OFF = 5.6μs/V BATT
CCV
GMV
C OUT
The switching frequency in continuous mode varies
according to the equation:
R CV
R OGMV
5 . 6 V x μ s x ?
+
f =
? 1 1 ?
1
?
? V SRC ? V BATT V BATT ?
C CV
REF
Figure 4. CCV Loop Diagram
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8731AETI+ | IC SMBUS LVL2 BATT CHRGR 28TQFN |
| MAX8734AEEI+ | IC PWR SUPPLY CONTROLLER 28QSOP |
| MAX8739ETP+T | IC DC/DC CONV W/OPAMP 20TQFN-EP |
| MAX8740ETB+T | IC CONV DC-DC TFT-LCD 10-TDFN |
| MAX8742EAI+ | IC CNTRLR PWR SUP 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8730EVKIT | 制造商:Maxim Integrated Products 功能描述:LOW COST BATTERY CHARGER - Rail/Tube |
| MAX8731AETI+ | 功能描述:电池管理 SMBus Level 2 Battery Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8731AETI+T | 功能描述:电池管理 SMBus Level 2 Battery Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8731AEVKIT+ | 功能描述:电源管理IC开发工具 MAX8731A Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8731AEVSYS | 功能描述:电池管理 Evaluation System for the MAX8731A (includes an EVKit and the Maxim SMBUSMON2 board) RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。