参数资料
| 型号： | MAX8741EAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/34页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PWR SUP 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 4.2 V ~ 30 V |
| 输出数： | 2 |
| 输出电压： | 3.3V，5V，2.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
500kHz Multi-Output Power-Supply Controllers
with High Impedance in Shutdown
The 2.5V reference (REF) is accurate to ±2% over tem-
perature, making REF useful as a precision system ref-
erence. Bypass REF to GND with 1μF (min). REF can
supply up to 5mA for external loads. (Bypass REF with
a minimum 1μF/mA reference load current.) However, if
extremely accurate specifications for both the main out-
put voltages and REF are essential, avoid loading REF
more than 100μA. Loading REF reduces the main out-
put voltage slightly, because of the reference load-
regulation error.
When the 5V main output voltage is above 4.5V, an inter-
nal p-channel MOSFET switch connects CSL5 to V L ,
while simultaneously shutting down the V L linear regula-
tor. This action bootstraps the IC, powering the internal
circuitry from the output voltage, rather than through a
linear regulator from the battery. Bootstrapping reduces
power dissipation due to gate charge and quiescent
losses by providing that power from a 90%-efficient
switch-mode source, rather than from a much-less-effi-
cient linear regulator.
Boost High-Side Gate-Drive Supply
(BST3 and BST5)
Gate-drive voltage for the high-side n-channel switches is
generated by a flying-capacitor boost circuit (Figure 2).
The capacitor between BST_ and LX_ is alternately
charged from the V L supply and placed parallel to the
high-side MOSFET’s gate-source terminals. On startup,
the synchronous rectifier (low-side MOSFET) forces LX_
to 0V and charges the boost capacitors to 5V. On the
second half-cycle, the SMPS turns on the high-side
MOSFET by closing an internal switch between BST_ and
DH_. This provides the necessary enhancement voltage
to turn on the high-side switch, an action that “boosts” the
5V gate-drive signal above the battery voltage.
Ringing at the high-side MOSFET gate (DH3 and DH5)
in discontinuous-conduction mode (light loads) is a nat-
ural operating condition. It is caused by residual ener-
gy in the tank circuit, formed by the inductor and stray
capacitance at the switching node, LX. The gate-drive
negative rail is referred to LX, so any ringing there is
directly coupled to the gate-drive output.
Current-Limiting and Current-Sense
Inputs (CSH and CSL)
The current-limit circuit resets the main PWM latch and
turns off the high-side MOSFET switch whenever the
voltage difference between CSH and CSL exceeds
100mV. This limiting is effective for both current flow
directions, putting the threshold limit at ±100mV. The
tolerance on the positive current limit is ±20%, so the
external low-value sense resistor (R1) must be sized for
80mV / I PEAK , where I PEAK is the required peak induc-
tor current to support the full load current, while compo-
nents must be designed to withstand continuous-
current stresses of 120mV/R1.
For breadboarding or for very-high-current applica-
tions, it may be useful to wire the current-sense inputs
with a twisted pair, rather than PC traces. (This twisted
pair need not be special; two pieces of wire-wrap wire
twisted together is sufficient.) This reduces the possible
noise picked up at CSH_ and CSL_, which can cause
unstable switching and reduced output current. The
CSL5 input also serves as the IC’s bootstrap supply
input. Whenever V CSL5 > 4.5V, an internal switch con-
nects CSL5 to V L .
Oscillator Frequency and
Synchronization (SYNC)
The SYNC input controls the oscillator frequency. Low
selects 333kHz; high selects 500kHz. SYNC can also
be used to synchronize with an external 5V CMOS or
TTL clock generator. SYNC has a guaranteed 400kHz
to 583kHz capture range. A high-to-low transition on
SYNC initiates a new cycle.
Operating at 500kHz optimizes the application circuit for
component size and cost; 333kHz operation provides
increased efficiency, lower dropout, and improved load-
transient response at low input-output voltage differ-
ences (see the Low-Voltage Operation section).
Shutdown Mode
Holding SHDN low puts the IC into its 4μA shutdown
mode. SHDN is logic input with a threshold of about 1V
(the V TH of an internal n-channel MOSFET). For automatic
startup, bypass SHDN to GND with a 0.01μF capacitor
and connect it to V+ through a 220k Ω resistor.
Power-Up Sequencing and
ON/ OFF Controls
Startup is controlled by RUN/ON3 and TIME/ON5 in
conjunction with SEQ. With SEQ connected to REF, the
two control inputs act as separate ON/ OFF controls for
each supply. With SEQ connected to V L or GND,
RUN/ON3 becomes the master ON/ OFF control input
and TIME/ON5 becomes a timing pin, with the delay
between the two supplies determined by an external
capacitor. The delay is approximately 800μs/nF. The
3.3V supply powers up first if SEQ is connected to V L ,
and the 5V supply is first if SEQ is connected to GND.
When driving TIME/ON5 as a control input with external
logic, always place a resistor (>1k Ω ) in series with the
input. This prevents possible crowbar current due to
the internal discharge pulldown transistor, which turns
on in standby mode and momentarily at the first power-
up or in shutdown mode.
______________________________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| SIP21107DVP-46-E3 | IC REG LDO 4.6V .15A SC75-6 |
| SIP21107DVP-45-E3 | IC REG LDO 4.5V .15A SC75-6 |
| SIP21107DVP-33-E3 | IC REG LDO 3.3V .15A SC75-6 |
| SIP21107DVP-30-E3 | IC REG LDO 3V .15A SC75-6 |
| SIP21107DVP-28-E3 | IC REG LDO 2.8V .15A SC75-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8741EAI+ | 功能描述:电流和电力监控器、调节器 500kHz Multi-Out Pwr Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8741EAI+T | 功能描述:电流和电力监控器、调节器 500kHz Multi-Out Pwr Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8741EAI-T | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8742EAI | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8742EAI+ | 功能描述:电流和电力监控器、调节器 500kHz Multi-Out Pwr Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。