参数资料
| 型号： | MAX8741EAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/34页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PWR SUP 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 4.2 V ~ 30 V |
| 输出数： | 2 |
| 输出电压： | 3.3V，5V，2.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
500kHz Multi-Output Power-Supply Controllers
with High Impedance in Shutdown
current to reverse at light loads. This results in fixed-fre-
quency operation and continuous inductor-current flow.
This eliminates discontinuous-mode inductor ringing
and improves cross-regulation of transformer-coupled
multiple-output supplies, particularly in circuits that do
not use additional secondary regulation through SECFB
or V DD .
In most applications, connect SKIP to GND to minimize
quiescent supply current. V L supply current with SKIP
high is typically 30mA, depending on external MOSFET
gate capacitance and switching losses.
Internal Digital Soft-Start Circuit
Soft-start allows a gradual increase of the internal cur-
rent-limit level at startup to reduce input surge currents.
Both SMPSs contain internal digital soft-start circuits,
each controlled by a counter, a digital-to-analog con-
verter (DAC), and a current-limit comparator. In shut-
down or standby mode, the soft-start counter is reset to
zero. When an SMPS is enabled, its counter starts
counting oscillator pulses, and the DAC begins incre-
menting the comparison voltage applied to the current-
limit comparator. The DAC output increases from 0 to
100mV in five equal steps as the count increases to
512 clocks. As a result, the main output capacitor
charges up relatively slowly. The exact time of the out-
put rise depends on output capacitance and load cur-
rent, and is typically 600μs with a 500kHz oscillator.
Dropout Operation
Dropout (low input-output differential operation) is
enhanced by stretching the clock pulse width to
increase the maximum duty factor. The algorithm fol-
lows: if the output voltage (V OUT ) drops out of regula-
tion without the current limit having been reached, the
SMPS skips an off-time period (extending the on-time).
At the end of the cycle, if the output is still out of regula-
tion, the SMPS skips another off-time period. This
action can continue until three off-time periods are
skipped, effectively dividing the clock frequency by as
much as four.
The typical PWM minimum off-time is 300ns, regardless
of the operating frequency. Lowering the operating fre-
quency raises the maximum duty factor above 97%.
Adjustable-Output Feedback
(Dual-Mode FB)
Fixed, preset output voltages are selected when FB_ is
connected to ground. Adjusting the main output volt-
age with external resistors is simple for any of the
MAX8741/MAX8742, through resistor-dividers connect-
ed to FB3 and FB5 (Figure 2). Calculate the output volt-
age with the following formula:
V OUT = V REF (1 + R1 / R2)
where V REF = 2.5V nominal.
The nominal output should be set approximately 1% or
2% high to make up for the MAX8741/MAX8742 -2% typ-
ical load-regulation error. For example, if designing for a
3.0V output, use a resistor ratio that results in a nominal
output voltage of 3.05V. This slight offsetting gives the
best possible accuracy. Recommended normal values
for R2 range from 5k Ω to 100k Ω . To achieve a 2.5V nom-
inal output, connect FB_ directly to CSL_.
Remote output-voltage sensing, while not possible in
fixed-output mode due to the combined nature of the
voltage-sense and current-sense inputs (CSL3 and
CSL5), is easy to do in adjustable mode by using the top
of the external resistor-divider as the remote sense point.
When using adjustable mode, it is a good idea to
always set the “3.3V output” to a lower voltage than the
“5V output.” The 3.3V output must always be less than
V L , so that the voltage on CSH3 and CSL3 is within the
common-mode range of the current-sense inputs. While
V L is nominally 5V, it can be as low as 4.7V when linear-
ly regulating, and as low as 4.2V when automatically
bootstrapped to CSH5.
Secondary Feedback Regulation Loop
(SECFB or V DD )
A flyback-winding control loop regulates a secondary
winding output, improving cross-regulation when the
primary output is lightly loaded or when there is a low
input-output differential voltage. If V DD or SECFB falls
below its regulation threshold, the low-side switch is
turned on for an extra 0.75μs. This reverses the induc-
tor (primary) current, pulling current from the output fil-
ter capacitor and causing the flyback transformer to
operate in forward mode. The low impedance present-
ed by the transformer secondary in forward mode
dumps current into the secondary output, charging up
the secondary capacitor and bringing V DD or SECFB
back into regulation. The secondary feedback loop
does not improve secondary output accuracy in normal
flyback mode, where the main (primary) output is heavi-
ly loaded. In this condition, secondary output accuracy
is determined by the secondary rectifier drop, trans-
former turns ratio, and accuracy of the main output
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| SIP21107DVP-46-E3 | IC REG LDO 4.6V .15A SC75-6 |
| SIP21107DVP-45-E3 | IC REG LDO 4.5V .15A SC75-6 |
| SIP21107DVP-33-E3 | IC REG LDO 3.3V .15A SC75-6 |
| SIP21107DVP-30-E3 | IC REG LDO 3V .15A SC75-6 |
| SIP21107DVP-28-E3 | IC REG LDO 2.8V .15A SC75-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8741EAI+ | 功能描述:电流和电力监控器、调节器 500kHz Multi-Out Pwr Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8741EAI+T | 功能描述:电流和电力监控器、调节器 500kHz Multi-Out Pwr Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8741EAI-T | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8742EAI | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8742EAI+ | 功能描述:电流和电力监控器、调节器 500kHz Multi-Out Pwr Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。