- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8745ETJ+ (Maxim Integrated Products)IC CNTRLR PWR SUP QUAD 32TQFN PDF资料下载
参数资料
| 型号： | MAX8745ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/36页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PWR SUP QUAD 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，1 V ~ 26 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
When adjusting both output voltages, set the 3.3V
SMPS lower than the 5V SMPS. LDO5 connects to the
5V output (CSL5) through an internal switch only when
CSL5 is above the LDO5 bootstrap threshold (4.5V)
and the soft-start sequence for the CSL5 side has com-
pleted. Bootstrapping works most effectively when the
fixed output voltages are used. Once LDO5 is boot-
strapped from CSL5, the internal 5V linear regulator
turns off. This reduces the internal power dissipation
and improves efficiency at higher input voltages.
Current-Limit Protection (ILIM)
The current-limit circuit uses differential current-sense
inputs (CSH_ and CSL_) to limit the peak inductor cur-
rent. If the magnitude of the current-sense signal
exceeds the current-limit threshold, the PWM controller
turns off the high-side MOSFET (Figure 3). The actual
maximum load current is less than the peak current-
limit threshold by an amount equal to half of the induc-
tor ripple current. Therefore, the maximum load
capability is a function of the current-sense resistance,
inductor value, switching frequency, and duty cycle
(V OUT /V IN ).
In forced-PWM mode, the MAX8744/MAX8745 also
implement a negative current limit to prevent excessive
reverse inductor currents when V OUT is sinking current.
The negative current-limit threshold is set to approxi-
mately 120% of the positive current limit and tracks the
positive current limit when ILIM is adjusted.
Connect ILIM to LDO5 for the 50mV default threshold,
or adjust the current-limit threshold with an external
resistor-divider at ILIM. Use a 2μA to 20μA divider cur-
rent for accuracy and noise immunity. The current-limit
MOSFET Gate Drivers (DH_, DL_)
The DH_ and DL_ drivers are optimized for driving
moderate-sized high-side and larger low-side power
MOSFETs. This is consistent with the low duty factor
seen in notebook applications, where a large V IN -
V OUT differential exists. The high-side gate drivers
(DH_) source and sink 2A, and the low-side gate dri-
vers (DL_) source 1.7A and sink 3.3A. This ensures
robust gate drive for high-current applications. The
DH_ floating high-side MOSFET drivers are powered by
charge pumps at BST_ while the DL_ synchronous-rec-
tifier drivers are powered directly by the fixed 5V linear
regulator (LDO5).
Adaptive dead-time circuits monitor the DL_ and DH_
drivers and prevent either FET from turning on until the
other is fully off. The adaptive driver dead-time allows
operation without shoot-through with a wide range of
MOSFETs, minimizing delays and maintaining efficiency.
There must be a low-resistance, low-inductance path
from the DL_ and DH_ drivers to the MOSFET gates for
the adaptive dead-time circuits to work properly; other-
wise, the sense circuitry in the MAX8744/ MAX8745 inter-
prets the MOSFET gates as “off” while charge actually
remains. Use very short, wide traces (50 mils to 100 mils
wide if the MOSFET is 1in from the driver).
The internal pulldown transistor that drives DL_ low is
robust, with a 0.6 Ω (typ) on-resistance. This helps prevent
DL_ from being pulled up due to capacitive coupling from
the drain to the gate of the low-side MOSFETs when the
FAULT
threshold adjustment range is from 50mV to 200mV. In
POWER-GOOD
PROTECTION
the adjustable mode, the current-limit threshold voltage
equals precisely 1/10 the voltage seen at ILIM. The
logic threshold for switchover to the default value is
0.9 x INT REF_
0.7 x INT REF_
1.11 x INT REF_
INTERNAL FB
approximately V LDO5 - 1V.
Carefully observe the PCB layout guidelines to ensure
that noise and DC errors do not corrupt the differential
current-sense signals seen by CSH_ and CSL_. Place
the IC close to the sense resistor with short, direct
traces, making a Kelvin-sense connection to the cur-
rent-sense resistor.
ENABLE OVP
ENABLE UVP
6144
CLK
FAULT
LATCH
FAULT
POWER-GOOD
POR
Figure 6. Power-Good and Fault Protection
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8751ETJ+T | IC CNTRLR CCFL INV 32-TQFN |
| MAX8752ETA+T | IC DC-DC CONV TFT LCD 8-TDFN |
| MAX8753ETI+T | IC DC-DC CONV TFT LCD 28TQFN |
| MAX8756ETI+T | IC CNTRL DUAL PS 28-TQFN |
| MAX8758ETG+T | IC REG STEP UP 24-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8745ETJ+ | 功能描述:电流和电力监控器、调节器 Quad-Out Main Power Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8745ETJ+T | 功能描述:电流和电力监控器、调节器 Quad-Out Main Power Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX874C/D | 功能描述:基准电压& 基准电流 RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
| MAX874CPA | 功能描述:基准电压& 基准电流 RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
| MAX874CPA+ | 功能描述:基准电压& 基准电流 RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。