- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8784ETL+T (Maxim Integrated Products)IC REG STP UP W/AMP 40-TQFN PDF资料下载
参数资料
| 型号： | MAX8784ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/24页 |
| 文件大小： | 0K |
| 描述： | IC REG STP UP W/AMP 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | LCD 电视机/监控器 |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
Step-Up Regulator, Internal Charge Pumps, Switch
Control, and Operational Amplifier for TFT LCDs
Positive Charge-Pump Regulator
The positive charge-pump regulator is typically used to
generate the positive supply rail for the TFT LCD gate
driver ICs. The positive charge pump is a two-stage
charge pump with external pump and reservoir capaci-
tors. The output voltage is set with an external resistive
voltage-divider from its output to GND with the midpoint
connected to FBP. The charge pump includes internal
switches with drivers to control the power transfer.
Figure 4 shows the block diagram of the positive
charge pump.
The controller regulates the positive charge-pump output
voltage so that V FBP = V REF . If V FBP goes below the refer-
ence, P1 and P3 are turned on when the rising edge of
the oscillator arrives, while the drivers pull C1N to GND
and C2N to SUP. The first stage flying capacitor C6
SUP
(Figure 4) is charged by the charge-pump supply input
and the second stage flying capacitor C7 is discharged
into the reservoir capacitor C8. After a fixed period, P2 is
turned on and P1 and P3 are turned off while C1N is
pulled to SUP and C2N is pulled to GND. C7 is charged
by C6 in preparation for the next pump cycle.
The MAX8784 implements a digital variable-resistance
algorithm to control the current delivered to the output.
The algorithm sets the on-resistance of the positive
charge-pump drivers according to the load current. The
on-resistance of the drivers is set by counting the num-
ber of charging pulses in the previous 12 oscillator
cycles. As the number of charging pulses in the previ-
ous 12 oscillator cycles increases, the on-resistance of
the switch is reduced. The number of charging pulses in
the previous 12 oscillator cycles is a measure of the load
current. The period of C1N and C2N switching is 1.66μs.
The positive charge-pump regulator’s startup can be
delayed by connecting an external capacitor from
? 2
GND
? 1
P1
01
GDEL to GND. An internal constant-current source
begins charging the GDEL capacitor when the negative
charge pump reaches regulation. When the GDEL volt-
age exceeds V REF , the positive charge-pump regulator
C6
C7
C1N
C1P
C2P
? 2
? 1
P2
P3
POUT
is enabled. Each time it is enabled, the positive charge-
pump regulator goes through a soft-start routine by
ramping up its internal reference voltage from 0 to V REF
in 128 steps. The soft-start period is 3ms (typ) and FBP
fault detection is disabled during this period. The soft-
start feature effectively limits the inrush current during
startup.
C2N
? 1
LCD DISABLE
COMPARATOR
C8
The MAX8784 monitors the FBP and SUP voltage to
detect fault conditions. If V FBP is continuously below
80% of its nominal regulation point for approximately
? 2
CONTROLLER
DISABLE
ERROR AMPLIFIER
1.1*REF
FBP
55ms, the MAX8784 sets a fault latch, shutting down all
outputs except the reference and operational amplifiers.
If SUP exceeds the SUP overvoltage faut threshold (20V,
REF
Figure 4. Positive Charge-Pump Regulator Control Block
Diagram
typ), LX switching is inhibited until SUP decreases.
Furthermore, if SUP exceeds its overvoltage charge-
pump inhibit level (21V, typ), positive charge-pump
switching is inhibited until SUP decreases to prevent
damage to the charge pump.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8785AETI+T | IC CCFL CTRL 28-TQFN |
| MAX8792ETD+T | IC PWM CTRLR STEP-DWN 14TDFN |
| MAX8794ETB+T | IC DDR LINEAR REG 10-TDFN |
| MAX8795AETJ+C7P | IC TFT-LCD DC/DC CONV 32-TQFN |
| MAX8798ETX+T | IC INTERNAL-SW BOOST REG 36-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8784EVKIT+ | 功能描述:显示开发工具 MAX8784 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8785AETI+ | 功能描述:显示驱动器和控制器 Full-Bridge CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8785AETI+T | 功能描述:显示驱动器和控制器 Full-Bridge CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8785AEVKIT# | 功能描述:LED 照明开发工具 MAX8785A Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8785ETI+ | 功能描述:显示驱动器和控制器 Full-Bridge CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。