- 您现在的位置：买卖IC网 > PDF目录296470 > MAX8795A+ (MAXIM INTEGRATED PRODUCTS INC) 1.6 A SWITCHING REGULATOR, 1400 kHz SWITCHING FREQ-MAX, QCC32 PDF资料下载
参数资料
| 型号： | MAX8795A+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 1.6 A SWITCHING REGULATOR, 1400 kHz SWITCHING FREQ-MAX, QCC32 |
| 封装： | 5 X 5 MM, 0.80 MM HEIGHT, LEAD FREE, MO-220WHHD-2, TQFN-32 |
| 文件页数： | 14/24页 |
| 文件大小： | 387K |
| 代理商： | MAX8795A+ |
MAX8795A
TFT-LCD DC-DC Converter with
Operational Amplifiers
_
__
_
2
21
1
Step-Up Regulator
The largest portions of power dissipation in the step-up
regulator are the internal MOSFET, the inductor, and the
output diode. If the step-up regulator has 90% efficiency,
approximately 3% to 5% of the power is lost in the internal
MOSFET, approximately 3% to 4% in the inductor, and
approximately 1% in the output diode. The remaining 1%
to 3% is distributed among the input and output capacitors
and the PCB traces. If the input power is about 5W, the
power lost in the internal MOSFET is approximately 150mW
to 250mW.
Operational Amplifier
The power dissipated in the operational amplifiers
depends on their output current, the output voltage,
and the supply voltage:
where IOUT_(SOURCE) is the output current sourced by
the operational amplifier, and IOUT_(SINK) is the output
current that the operational amplifier sinks.
In a typical case where the supply voltage is 13V and
the output voltage is 6V with an output source current
of 30mA, the power dissipated is 180mW.
PCB Layout and Grounding
Careful PCB layout is important for proper operation.
Use the following guidelines for good PCB layout:
Minimize the area of high-current loops by placing
the inductor, the output diode, and the output
capacitors near the input capacitors and near the
LX and PGND pins. The high-current input loop
goes from the positive terminal of the input capacitor
to the inductor, to the IC’s LX pin, out of PGND, and
to the input capacitor’s negative terminal. The high-
current output loop is from the positive terminal of
the input capacitor to the inductor, to the output
diode (D1), and to the positive terminal of the output
capacitors, reconnecting between the output capac-
itor and input capacitor ground terminals. Connect
these loop components with short, wide connec-
tions. Avoid using vias in the high-current paths. If
vias are unavoidable, use many vias in parallel to
reduce resistance and inductance.
Create a power-ground island (PGND) consisting of
the input and output capacitor grounds, PGND pin,
and any charge-pump components. Connect all of
these together with short, wide traces or a small
ground plane. Maximizing the width of the power-
ground traces improves efficiency and reduces out-
put voltage ripple and noise spikes. Create an
analog ground plane (AGND) consisting of the
AGND pin, all the feedback-divider ground connec-
tions, the operational-amplifier divider ground con-
nections, the COMP and DEL capacitor ground
connections, and the device’s exposed backside
paddle. Connect the AGND and PGND islands by
connecting the PGND pin directly to the exposed
backside paddle. Make no other connections
between these separate ground planes.
Place all feedback voltage-divider resistors within
5mm of their respective feedback pins. The divider’s
center trace should be kept short. Placing the resis-
tors far away causes their FB traces to become
antennas that can pick up switching noise. Take
care to avoid running any feedback trace near LX or
the switching nodes in the charge pumps, or pro-
vide a ground shield.
Place the IN pin and REF pin bypass capacitors as
close as possible to the device. The ground connec-
tion of the IN bypass capacitor should be connected
directly to the AGND pin with a wide trace.
Minimize the length and maximize the width of the
traces between the output capacitors and the load
for best transient responses.
Minimize the size of the LX node while keeping it
wide and short. Keep the LX node away from feed-
back nodes (FB, FBP, and FBN) and analog ground.
Use DC traces to shield if necessary.
Refer to the MAX8795A evaluation kit for an example of
proper PCB layout.
PD
I
V
PD
I
V
SOURCE
OUT
SOURCE
SUP
OUT
SINK
OUT
SINK
OUT
=×
=×
_(
)
_
_(
)
_
()
Chip Information
TRANSISTOR COUNT: 6595
PROCESS: BiCMOS
相关PDF资料 |
PDF描述 |
|---|---|
| MAX879CSA | IC LOGIC 16213 24-BIT FET BUS-EXCHANGE SWITCH -40+85C TSSOP-56 1500/REEL |
| MAX9851EVCMODU | MAX9851评估板/评估系统 |
| MAX9934FART+T | SPECIALTY ANALOG CIRCUIT, PBGA6 |
| MAX9950FCCB | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| MAX9966BGCCQ+D | Quad, Low-Power, 500Mbps ATE Driver/Comparator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8795AETJ+ | 功能描述:直流/直流开关转换器 TFT-LCD DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX8795AETJ+C7P | 功能描述:显示驱动器和控制器 TFT-LCD DC/DC Converter RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8795AETJ+T | 功能描述:LCD 驱动器 TFT-LCD DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8795AEVKIT+ | 功能描述:电源管理IC开发工具 MAX8795A Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8795AGCJ/V+ | 功能描述:LCD 驱动器 TFT-LCD DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。