- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8819AETI+T (Maxim Integrated Products)IC PMIC W/INT CHARGER 28TQFN-EP PDF资料下载
参数资料
| 型号： | MAX8819AETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/29页 |
| 文件大小： | 0K |
| 描述： | IC PMIC W/INT CHARGER 28TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 手持/移动设备 |
| 电源电压： | 4.1 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
PMIC with Integrated Chargers and Smart
Power Selector in a 4mm x 4mm TQFN
? The battery charger is enabled by the processor dri-
ving the CEN input high. A valid input must be avail-
able at DC. The battery charger is disabled without
a valid input at DC or by driving CEN low.
? The system current has priority over the battery
FAST-CHARGE, PREQUALIFICATION, AND TOP-OFF
CURRENT vs. CHARGE-SETTING RESISTOR
10,000
charger; the battery charger automatically reduces
its charge current to maintain the input current limit
while still providing the system current (I SYS ).
? The input current limit is tapered down from full cur-
rent to zero current when the die temperature transi-
tions from +100°C to +120°C. Since I SYS has priority
over the battery charge current, the battery charge
current tapers down before I SYS . The overall result is
self-regulation of die temperature (see the Thermal
1000
100
10
1
I CHGMAX
I PREQUAL, I TOPOFF
Limiting and Overload Protection section for more
0
5
10
15
20
information).
? The battery charger stops charging in done mode
as shown in Figures 2 and 3.
Charge Status Output ( CHG )
CHG is an open-drain, active-low output that indicates
charger status. As shown in Figures 2 and 3, CHG is
R CISET (k Ω )
Figure 4. Calculated Charge Currents vs. R CISET
Table 2. Calculated Charge Currents vs.
R CISET
low when the charger is in its prequalification or fast-
charge states. When a timer count is exceeded in
either state, CHG indicates the fault by blinking at a
2Hz rate and remains in that state until the charger is
reset by CEN going low, removal of DC or setting
DLIM[1:2] = 11.
When the MAX8819_ is used with a microprocessor
(μP), connect a pullup resistor between CHG and the
system logic voltage to indicate charge status to the
μP. Alternatively, CHG sinks up to 20mA for an LED
charge indicator.
If the charge status output feature is not required, con-
nect CHG to ground or leave unconnected.
Charge Timer
As shown in Figure 3, a fault timer prevents the battery
from charging indefinitely. In prequalification mode, the
charge time is internally fixed to 33min.
R CISET (k Ω )
3.01
4.02
4.99
6.04
6.98
8.06
9.09
10
11
12.1
13
14
15
I CHGMAX
(mA)
1000
746
601
497
430
372
330
300
273
248
231
214
200
I PREQUAL
(mA)
100
75
60
50
43
37
33
30
27
25
23
21
20
I TOPOFF
(mA)
100
75
60
50
43
37
33
30
27
25
23
21
20
t PREQUAL = 33min
In fast-charge mode, the charge timer is internally fixed
to 660min.
t FSTCHG = 660min
When the charger exits fast-charge mode, a fixed
33min top-off mode is entered:
t TOPOFF = 33min
While in the constant-current fast-charge mode (Figure
2), if the MAX8819_ reduces the battery charge current
due to its internal die temperature or large system loads,
it slows down the charge timer. This feature eliminates
nuisance charge timer faults. When the battery charge
current is between 100% and 50% of its programmed
fast-charge level, the fast-charge timer runs at full
speed. When the battery charge current is between
50% and 20% programmed fast-charge level, the fast-
charge timer is slowed by 2x. Similarly, when the bat-
tery charge current is below 20% of the programmed
fast-charge level, the fast-charge timer is paused. The
fast-charge timer is not slowed or paused when the
charger is in the constant voltage portion of its fast-
charge mode (Figure 2) where the charge current
reduces normally.
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8819BETI+T | IC PMIC W/INT CHARGER 28-TQFN |
| MAX881REUB | IC LOW NOISE IS SUPP FET10-uMAX |
| MAX882CPA+ | IC REG LDO 3.3V/ADJ .2A 8-DIP |
| MAX8833ETJ+T | IC REG BUCK ADJ 3A DL 32TQFN |
| MAX8841ELT15+T | IC REG LDO 1.5V .15A 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8819AEVKIT+ | 功能描述:PMIC 解决方案 Evaluation Kit for the MAX8819A MAX8819B MAX8819C and MAX8819D RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819BETI+ | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819BETI+T | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819CETI+ | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819CETI+T | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。