- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8819AETI+T (Maxim Integrated Products)IC PMIC W/INT CHARGER 28TQFN-EP PDF资料下载
参数资料
| 型号： | MAX8819AETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 28/29页 |
| 文件大小： | 0K |
| 描述： | IC PMIC W/INT CHARGER 28TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 手持/移动设备 |
| 电源电压： | 4.1 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页
PMIC with Integrated Chargers and Smart
Power Selector in a 4mm x 4mm TQFN
OUT_
GATE DRIVE
R T
TO SWITCH
5V/div
0V
FB_
R B
R D
V1 3V
RST1
3.3V
3.35V
500mV/div
3V
4.2V
2V/div
100 μ s/div
R PAR =
? 1
R D =
?
R T = R B × ? OUTL ? 1 ?
Figure 9. Dynamic Output Voltage Control
current is first reduced by lowering charge current. If
the junction temperature still reaches +120°C in spite of
charge current reduction, no input current is drawn
from DC; the battery supplies the entire load and SYS is
regulated 70mV below BAT.
Regulator Thermal-Overload Shutdown
The IC disables all regulator outputs and the battery
charger when the junction temperature rises above
+165°C, allowing the device to cool. When the junction
temperature cools by approximately 15°C the regula-
tors and charger resume the state indicated by the
enable input (EN123, EN4, and CEN) by repeating their
soft-start sequence. Please note that this thermal-over-
load shutdown is a fail-safe mechanism; proper thermal
design should ensure that the junction temperature of
the MAX8819_ never exceeds the absolute maximum
rating of +150°C.
Applications Information
Dynamic Output Voltage Adjustment
for Step-Down Converters
Dynamic output voltage adjustment can be implement-
ed for the step-down converter by adding a resistor
and a switch from FB_ to GND. See Figure 9.
To calculate the resistor-divider, start with the lower
voltage desired and calculate the resistor-divider using
R T and R B only. Setting R B = 100k Ω is acceptable. Use
the following equation to calculate R T :
? V ?
? V FB ?
where V OUTL is the desired lower output voltage and
V FB is the feedback regulation voltage, 1V (typ).
Figure 10. Dynamic Voltage Adjustment with Example Values
R D is calculated using the higher set voltage and the
following equations assuming the switch resistance is
negligible:
R T
V OUTH
V FB
1
1 1
R PAR R B
where R PAR is the parallel resistance of R B and R D ,
V OUTH is the higher set voltage, and V FB is the feed-
back regulation voltage, 1V (typ).
For example, if V OUTL = 3V, V OUTH = 3.3V, R B =
100k Ω , then:
R T = 100k Ω x ((3V/1V) - 1) = 200k Ω
R PAR = 200k Ω /((3.3V/1V) - 1) = 86.96k Ω
R D = 1/((1/86.96k Ω ) - (1/100k Ω )) = 666.7k Ω
Choose R D = 665k Ω as the closest standard 1% value.
CH1 = gate drive to switch
CH2 = V1, 1V offset; 3V to 3.3V to 3V, 10 Ω load
CH3 = RST1
The scope plot (Figure 10) shows V1 switching from 3V
to 3.3V to 3V with the resistor values of the example.
When the switch is turned on, V1 slews from 3V to 3.3V
in about 20μs, which is less than the 50μs RST1 de-
glitch filter, and therefore, RST1 does not trip. When the
switch is turned off, V1 soars to about 3.35V due to the
energy in the inductor. Since V1 is above the regulation
voltage, REG1 skips until V1 decays to the regulation
voltage. The decay rate is determined by the output
capacitance and the load. In this example, the output
capacitance is 10μF and the load is 10 Ω , so the time
28
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8819BETI+T | IC PMIC W/INT CHARGER 28-TQFN |
| MAX881REUB | IC LOW NOISE IS SUPP FET10-uMAX |
| MAX882CPA+ | IC REG LDO 3.3V/ADJ .2A 8-DIP |
| MAX8833ETJ+T | IC REG BUCK ADJ 3A DL 32TQFN |
| MAX8841ELT15+T | IC REG LDO 1.5V .15A 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8819AEVKIT+ | 功能描述:PMIC 解决方案 Evaluation Kit for the MAX8819A MAX8819B MAX8819C and MAX8819D RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819BETI+ | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819BETI+T | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819CETI+ | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819CETI+T | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。