- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8856ETD+T (Maxim Integrated Products)IC BATT CHARGER LI+ 1CELL 14TDFN PDF资料下载
参数资料
| 型号： | MAX8856ETD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI+ 1CELL 14TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 0 V ~ 14 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
USB/AC Adapter, Li+ Linear Battery Charger
with Integrated 50m Ω Battery Switch in TDFN
Thermal Regulation
The MAX8856 features a thermal limit that reduces the
charge current when the die temperature exceeds
+100°C. As the temperature increases, the IC lowers
the charge current by 50mA/°C above +100°C.
Capacitor Selection
Connect a ceramic capacitor from SYS to GND as
close to the IC as possible for proper stability. Use a
4.7μF X5R ceramic capacitor for most applications.
USB/AC-ADAPTER
OVP UP TO 14V
C1
4.7 μ F
IN
GND
V I/O
C HG
POK
D1
STATUS
INDICATORS
R2 R3
1k Ω 100k Ω
C4
0.1 μ F
Connect a 4.7μF ceramic capacitor from IN to GND as
close to the IC as possible. Use a larger input bypass
capacitor to reduce supply noise.
C3
0.1 μ F
V L
MAX8856
SYS
+3.5V TO +4.2V
C2
4.7 μ F
Thermal Considerations
EN1
The MAX8856 is available in a thermally enhanced
TDFN package with exposed paddle. Connect the
exposed paddle to a large copper ground plane to pro-
EN2
GATE
BAT
2.6V
60k Ω
vide a good thermal contact between the device and
the circuit board. The exposed paddle transfers heat
SETI
THM
away from the device, allowing the MAX8856 to charge
the battery with maximum current while minimizing the
increase in die temperature.
R1
23.58k Ω
T1
47k Ω
NTC
4.2V Li+
DC Input Sources
The MAX8856 operates from well-regulated DC
sources. The full-charging input voltage range is 4.25V
to 5.8V. The device survives input voltages up to 14V
without damage to the IC. If V IN is greater than 5.8V
(typ), the IC stops charging. An appropriate power sup-
ply must provide at least 4.25V when sourcing the
desired peak charging current. It also must stay below
5.8V when unloaded.
Application Circuits
Stand-Alone Li+ Charger
The MAX8856 provides a complete Li+ charging solu-
tion. Figure 3 shows the MAX8856 as a stand-alone Li+
battery charger. The 23.58k Ω resistor connected to
SETI sets a charging current of 712mA (typ). The LED
indicates when either prequal or fast-charging has
begun. When the battery is charged the LED turns off.
USB Application with AC Adapter
The MAX8856 can be configured for USB applications
with an optional AC-adapter input (Figure 4). The p-
channel MOSFET disconnects the USB port when the
AC adapter is installed. Alternately, the USB port and
AC adapter may be excluded from each other by
mechanical means, such as using a single connector.
USB-Powered Li+ Charger
The universal serial bus (USB) provides a high-speed
serial communication port, as well as power for the
Figure 3. Stand-Alone Application
remote device. The MAX8856 can be configured to
charge a battery at the highest current possible from
the host port. Figure 5 shows the MAX8856 as a USB
battery charger. To make the circuit compatible with
either 100mA or 500mA USB ports, the system software
begins at 100mA charging current. The microprocessor
then enumerates with the host to determine its current
capability. If the host port is capable, the charging cur-
rent is increased to 475mA to avoid exceeding the
500mA USB specification.
Layout and Bypassing
Place the input capacitor as close to the device as pos-
sible. Provide a large copper ground plane to allow the
exposed paddle to sink heat away from the device.
Connect the battery to BAT as close to the device as
possible to provide accurate battery voltage sensing.
Make all high-current traces short and wide to minimize
voltage drops. A sample layout is available in the
MAX8856 evaluation kit to help speed designs.
Chip Information
PROCESS: BiCMOS
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8860EUA33+ | IC REG LDO 3.3V/ADJ .3A 8-UMAX |
| MAX8862RESE+T | IC REG LDO 2.85V/ADJ 16-SOIC |
| MAX8863REUK+T | IC REG LDO 2.8V/ADJ .12A SOT23-5 |
| MAX8865TEUA+ | IC REG LDO 3.15V/ADJ .1A 8UMAX |
| MAX8868EUK30+T | IC REG LDO 3V .15A SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8857AETL+ | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 7-CHANNEL 2 AA DSC PMIC - Rail/Tube |
| MAX8857AETL+T | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 7-CHANNEL 2 AA DSC PMIC - Tape and Reel |
| MAX8858ETJ+ | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 6-CHANNEL DSC PMIC IN A 5MM X - Rail/Tube |
| MAX8858ETJ+T | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 6-CHANNEL DSC PMIC IN A 5MM X - Tape and Reel |
| MAX8860ESA33 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。