- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8856ETD+T (Maxim Integrated Products)IC BATT CHARGER LI+ 1CELL 14TDFN PDF资料下载
参数资料
| 型号： | MAX8856ETD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI+ 1CELL 14TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 0 V ~ 14 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
USB/AC Adapter, Li+ Linear Battery Charger
with Integrated 50m Ω Battery Switch in TDFN
Table 1. Logic Controls
Table 2. Charger Operation Truth Table
EN1
0
0
1
1
EN2
0
1
0
1
MODE
100mA
500mA
8000 x 2.1V / R SET
Suspend
GATE
Low
Low
Low
SUSPEND
MODE
No
No
No
CHARGER
PRESENT
No
No
Yes
V BAT >
3.5V
No
Yes
No
MOSFET
SWITCH
Closed
Closed
Open
Low
Low
No
Yes
Yes
Yes
Yes
No
Closed
Closed
V L Internal Voltage Regulator
The MAX8856 linear charger contains an internal linear
Low
High
Yes
X
Yes
X
Yes
X
Closed
Open
regulator to supply the power for the IC. Bypass V L to
GND with a 0.1μF ceramic capacitor. V L is regulated to
3.3V whenever the input voltage is above the battery
voltage and can source up to 500μA for external loads.
CHG Charge Indicator Output
CHG is an open-drain output that indicates charger sta-
tus and can be used with an LED. CHG goes low during
charging. CHG goes high impedance when V BAT equals
4.2V and the charging current drops below 50mA, or
when the MAX8856 is in suspend mode. When the
MAX8856 is used in conjunction with a microprocessor
(μP), connect a pullup resistor between CHG and the
logic I/O voltage to indicate charge status to the μP.
Soft-Start
To prevent input transients, the rate of change of the
charge current is limited when the charger is turned on
or changes its current compliance. It takes approxi-
mately 1ms for the charger to go from 0mA to the maxi-
mum fast-charge current.
THM Input
The MAX8856 monitors the battery temperature with an
external NTC thermistor that is in close thermal contact
with the battery. Select a thermistor resistance that is
47k Ω at +25°C and has a beta of 3400 Kelvins. The IC
compares the voltage at THM to an internal reference
voltage generated from V L and suspends charging
when it is greater than 0.542 x V L or less than 0.225 x
V L . Connect THM to GND to disable the temperature
control function.
GATE Input and SYS Output
The MAX8856 contains a SYS output that delivers up to
1A RMS at 3.5V to 4.2V to power an external system.
Bypass SYS to GND with a 4.7μF or larger ceramic
capacitor. When V BAT exceeds 3.5V or when the
MAX8856 is in suspend mode, and the GATE signal is
low, the MAX8856 internally connects SYS to BAT
through a 50m Ω switch. When the GATE signal is dri-
ven HIGH, the SYS to BAT switch is held open, regard-
less of operating condition. See Tables 1 and 2 for
more information.
When charging a battery, the load on SYS is serviced first
and the remaining available current goes to charge the
battery. SYS is connected to BAT when V IN is not valid.
POK
The MAX8856 contains an open-drain POK output that
goes low when a valid input source is detected at IN. A
valid input source is one whose voltage is between 4V
and 5.8V and exceeds the battery voltage by 250mV.
After a valid input has been established, charging is
sustained with inputs as low as 3.5V as long as the
input voltage remains above the battery voltage by at
least 55mV. POK is high impedance otherwise.
Applications Information
Charge-Current Selection
For USB applications, the charging current is internally
limited to 100mA or 500mA. For wall-cube applications
requiring a different current requirement, set the charg-
ing current with an external resistor from SETI to GND
(R SETI ). Calculate R SETI as follows:
R SETI = 8000 x 2.1V/(I BAT + I SYS )
where EN1 = high and EN2 = low.
The SETI input also enables the user to monitor the
charging current. Under fast-charge operation, the
SETI voltage regulates to 1.4V ( EN1 low and EN2 high)
or 2.1V ( EN1 high and EN2 low). As the charging cur-
rent decreases, V SETI decreases. This is due to either
the thermal regulation control or voltage regulation con-
trol (4.2V) of the MAX8856. V SETI is calculated using
the following equation:
V SETI = (I BAT + I SYS ) x R SETI /8000
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8860EUA33+ | IC REG LDO 3.3V/ADJ .3A 8-UMAX |
| MAX8862RESE+T | IC REG LDO 2.85V/ADJ 16-SOIC |
| MAX8863REUK+T | IC REG LDO 2.8V/ADJ .12A SOT23-5 |
| MAX8865TEUA+ | IC REG LDO 3.15V/ADJ .1A 8UMAX |
| MAX8868EUK30+T | IC REG LDO 3V .15A SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8857AETL+ | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 7-CHANNEL 2 AA DSC PMIC - Rail/Tube |
| MAX8857AETL+T | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 7-CHANNEL 2 AA DSC PMIC - Tape and Reel |
| MAX8858ETJ+ | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 6-CHANNEL DSC PMIC IN A 5MM X - Rail/Tube |
| MAX8858ETJ+T | 制造商:Maxim Integrated Products 功能描述:SMALLEST, ALL-INTERNAL MOSFET, 6-CHANNEL DSC PMIC IN A 5MM X - Tape and Reel |
| MAX8860ESA33 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。