- 您现在的位置：买卖IC网 > PDF目录13580 > MAX8969EWL33+T (Maxim Integrated Products)IC REG BOOST SYNC 3.3V 1A 9WLP PDF资料下载
参数资料
| 型号： | MAX8969EWL33+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC 3.3V 1A 9WLP |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 2.5 V ~ 5.5 V |
| 频率 - 开关： | 3MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 9-WFBGA，WLBGA |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 9-WLP（1.3x1.3） |
MAX8969
Step-Up Converter
for Handheld Applications
The IC is designed to operate with the input voltage
range straddling its output voltage set point. Two tech-
niques are used to accomplish this. The first technique is
to activate ATM if the input voltage exceeds 95% of the
output set point; see the Automatic Track Mode (ATM)
section. The second technique is automatic frequency
adjustment.
?
?
In track and ATM, current is limited to prevent
excessive inrush current during soft-start and to
protect against overload conditions. If the die tem-
perature exceeds +165°C in track/ATM, the switch
turns off until the die temperature has cooled to
+145 N C.
In boost mode, during each 3MHz switching cycle,
Automatic Track Mode (ATM)
ATM is entered when an internal comparator signals that
the input voltage has exceeded the ATM threshold. The
ATM threshold is 95% of the output voltage target. At this
point, the IC enters ATM, with the pMOS switch turned
on, regardless of the status of TREN. Note that EN must
be high to enable ATM mode. This behavior is summa-
rized in Table 1.
Automatic Frequency Adjustment
Automatic frequency adjustment is used to maintain
stability if the input voltage is above 80% and below
95% of the output set point. Frequency adjustment is
required because the n-channel has a minimum on-time
of approximately 60ns. At 3MHz, this would lead to the
p-channel having a maximum duty factor of 82%. With
an input voltage more than 82% of the output set point,
the p-channel’s duty factor must be increased by reduc-
ing operating frequency either through cycle skipping
or adjusting the clock’s frequency. The IC adjusts its
clock frequency rather than simply skipping cycles. This
adjustment is done in two steps. The first step occurs if
the input voltage exceeds approximately 83% of the out-
put voltage and reduces clock speed to approximately
1.6MHz. The second step occurs if the input voltage is
greater than output voltage less 460mV. If this condition
is met, clock frequency is reduced to approximately
1MHz. Frequency adjustment allows the converter to
operate at a known frequency under all conditions.
Fault Protection
In track, ATM, and boost modes, the IC has protection
against overload and overheating.
Table 1. Modes of Operation
if the inductor current exceeds 2.6A, the n-channel
MOSFET is shut off and the p-channel MOSFET is
switched on. The end result is that LX_ current is
regulated to 2.6A or less. A 2.6A inductor current
is a large enough current to guarantee a 1A output
load current under all intended operating conditions.
The IC can operate indefinitely while regulating the
inductor current to 2.6A or less.
However, if a short circuit or extremely heavy load is
applied to the output, the output voltage decreases since
the inductor current is limited to 2.6A.
If the output voltage decreases to less than 72% of the
regulation voltage target (i.e., 2.8V with V OUT_TARGET of
3.7V), a short circuit is assumed, and the IC returns to
the shutdown state. The IC then attempts to start up if the
output short is removed. Even if the output short persists
indefinitely, the IC thermal protection ensures that the die
is not damaged.
True Shutdown
During operation in boost mode, the p-channel MOSFET
prevents current from flowing from OUT_ to LX_. In all
other modes of operation, it is desirable to block current
flowing from LX_ to OUT_. True Shutdown prevents current
from flowing from LX_ to OUT_ while the IC is shut down
by reversing the internal body diode of the p-channel
MOSFET. This feature is also active during track/ATM to
allow current limit to function as anticipated.
Upon leaving boost mode, the p-channel MOSFET
continues to prevent current from flowing from OUT_ to
LX_ until OUT_ and IN are approximately the same volt-
age. After this condition has been met, track/ATM and
shutdown operate normally.
V IN COMPARATOR
X
X
0
1
EN
0
0
1
1
TREN
0
1
X
X
True Shutdown
Track
Boost
ATM
MODE OF OPERATION
X = Don't care.
12
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| SCB63C-331 | INDUCTOR SMD 330UH 0.11A 1KHZ |
| MAX8969EWL37+T | IC REG BOOST SYNC 3.7V 1A 9WLP |
| SCB63C-330 | INDUCTOR SMD 33UH 0.42A 1KHZ |
| SCB63C-2R2 | INDUCTOR SMD 2.2UH 1.60A 1KHZ |
| SCB63C-271 | INDUCTOR SMD 270UH 0.12A 1KHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8969EWL35+T | 功能描述:直流/直流开关转换器 600mA Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX8969EWL37+T | 功能描述:直流/直流开关转换器 1A Boost Converter with Track mode RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX8969EWL42+T | 功能描述:直流/直流开关转换器 1A Boost Converter with Track mode RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX8969EWL50+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX8969EWL50+T | 制造商:Maxim Integrated Products 功能描述:1A BOOST CONVERTER FOR LOW INPUT BATTERY TECHNOLOGIES - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。