- 您现在的位置：买卖IC网 > PDF目录11669 > MAX9621AUB+ (Maxim Integrated Products)IC HALL EFFECT SENSOR 10UMAX PDF资料下载
参数资料
| 型号： | MAX9621AUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC HALL EFFECT SENSOR 10UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 霍尔效应传感器 |
| 输入类型： | 逻辑 |
| 输出类型： | 模拟，数字 |
| 接口： | 2 线 |
| 电流 - 电源： | 1mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 管件 |
3
Maxim Integrated
Dual, 2-Wire Hall-Effect Sensor Interface with
Analog and Digital Outputs
MAX9621
DC ELECTRICAL CHARACTERISTICS (continued)
(VBAT = 13.6V, VSLEEP = 5V, IN1 = IN2 = no connection, RSET = 61.9kI to BAT, RPU = 10kI at DOUT1 and DOUT2, RL = 5kI to
GND at AOUT1 and AOUT2, unless otherwise noted, TA = -40NC to +125NC. Typical values are at TA = +25NC.) (Note 1)
Note 1: All DC specifications are 100% production tested at TA = +25°C. AC specifications are guaranteed by design at TA =
+25°C.
Note 2: Parameters that change with the value of the RSET resistor: IIH, IIL, IIN_HYS, ISC, tBL, tRAMP, tDEL, fMAX, and PR.
Note 3: Following power-up or startup from sleep mode, the start of the blanking period is delayed 20Fs.
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Input Referred Current Offset
IOS
Inferred from measurements at
IIN = -5mA, -14mA
-120
+120
F
A
AOUT_ Dropout Voltage
VBAT = 5.5V,
for 5% current
reduction
IIN = -14mA
0.85
1.6
V
IIN = -20mA
1.09
1.75
AOUT_ Output Impedance
500
MI
LOGIC I/O (DOUT1, DOUT2)
Output-Voltage Low DOUT1,
DOUT2
VOL
Sink current = 1mA
0.4
V
Three-State Output Current
DOUT1, DOUT2
IOZ
VSLEEP = 0V, 0V P VDOUT_ P 5V
±1
F
A
SLEEP
Input-Voltage High
VIH
2.0
V
Input-Voltage Low
VIL
0.8
V
Input Resistance to GND
RIN
50
100
kI
AC TIMING CHARACTERISTICS
Shutdown Delay from SLEEP
Low to IN_ Shutoff
tSHDN
IIH = -14mA to GND, time from SLEEP low
to IN_ drop 500mV, CL = 20pF
33
40
46
F
s
IN_, Blanking Time at Hall
Sensor Power-Up
tBL
IIH = -14mA to GND, time from
VIN_ = 500mV until DOUT_ high, CL =
20pF (Notes 2, 3)
76
89
103
F
s
IN_, Current Ramp Rate After
Turn-On
tRAMP
IN_ = GND (Note 2)
3.6
5
6.7
mA/Fs
Delay from IN_ to DOUT_ (Filter
Delay)
tDEL
From IIH to IIL or from IIL to IIH,
CL = 20pF, Figure 1 (Note 2)
10.8
13.5
16
F
s
Delay Difference Between
Rising and Falling Edges of
Both Channels
tDM
CHALL-BYPASS = 0.01FF, IIH = -11.5mA
and IIL = -7.5mA, CL = 20pF
1
F
s
Delay Difference Between
Channels
tCC
CHALL-BYPASS = 0.01FF, IIH = -11.5mA
and IIL = -7.5mA, CL = 20pF
500
ns
Maximum Frequency on Hall
Inputs
fMAX
CHALL-BYPASS = 0.01FF, IIH = -11.5mA
and IIL = -7.5mA, CL = 20pF (Note 2)
34
39
kHz
Maximum Analog Output
Current During Short-to-GND
Fault
IMAO
-1.4
mA
IN_ Pulse Length Rejected by
Filter to DOUT_
PR
Figure 2 (Note 2)
7.8
11.5
14.6
F
s
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J40-IW-F1 | CONVERTER MOD DC/DC 5V 100W |
| AD2S82ALPZ | IC CONV R/D MONO VAR RES 44PLCC |
| VI-J40-IW-F2 | CONVERTER MOD DC/DC 5V 100W |
| 638831-3 | CONN JACK SMB FAKRA BLUE |
| 1-2081205-3 | CONN JACK SMA CRIMP .047" S/R |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9621AUB/V+ | 功能描述:板机接口霍耳效应/磁性传感器 Dual 2-Wire Hall-Effect Sensor Interface with Analog and Digital Outputs RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| MAX9621AUB/V+T | 功能描述:板机接口霍耳效应/磁性传感器 Dual 2-Wire Hall-Effect Sensor Interface with Analog and Digital Outputs RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| MAX9621AUB+ | 功能描述:板机接口霍耳效应/磁性传感器 Hall Sensor Interface RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| MAX9621AUB+T | 功能描述:板机接口霍耳效应/磁性传感器 Hall Sensor Interface RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| MAX9621EVKIT+ | 功能描述:板机接口霍耳效应/磁性传感器 Hall Sensor Interface RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
发布紧急采购，3分钟左右您将得到回复。