- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9720AEUE+T (Maxim Integrated Products)IC AMP AUDIO .05W STER 16TSSOP PDF资料下载
参数资料
| 型号： | MAX9720AEUE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/21页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO .05W STER 16TSSOP |
| 标准包装： | 2,500 |
| 系列： | DirectDrive®, SmartSense™ |
| 类型： | AB 类 |
| 输出类型： | 耳机，2-通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 50mW x 2 @ 32 欧姆 |
| 电源电压： | 1.8 V ~ 3.6 V |
| 特点： | 消除爆音，短路保护和热保护，关闭 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 16-TSSOP |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
MAX9720
For automatic headphone detection, connect HPS to the
control pin of a 3-wire headphone jack, as shown in
Figure 7. With no headphone present, the output imped-
ance of the amplifier pulls HPS to less than 0.8 x VDD.
When a headphone plug is inserted into the jack, the
control pin is disconnected from the tip contact, and
HPS is pulled to VDD through the internal 100k
pullup.
A debounce delay controls the time between HPS going
high and the initiation of the SmartSense test sequence.
This time is controlled by an external capacitor on the
TIME pin and allows the user to customize the de-
bounce time (see the TIME Capacitor section).
Shutdown
Driving MODE1 and MODE2 to GND shuts down the
MAX9720, disconnects the internal HPS pullup resistor,
disables the charge pump and amplifiers, sets the
amplifier output impedance to 1k
, and reduces sup-
ply current to less than 6A.
Forced Mono Mode
In forced left mono mode (MODE1 = high, MODE2 =
low), the right channel is disabled and OUTR goes high
impedance. The stereo signal inputs are combined
through the mixer/attenuator and output on the left
channel. In forced mono mode, the SmartSense routine
is disabled.
Forced Stereo Mode
In forced stereo mode (MODE1 = low, MODE2 = high),
the device operates as a stereo headphone amplifier.
In forced stereo mode, the SmartSense routine is dis-
abled.
A
AL
LE
ER
RT
T Output
The MAX9720 includes an active-low, open-drain
ALERT output that indicates to the master device that
SmartSense has detected a fault condition. ALERT trig-
gers when an output short circuit is detected through
the SmartSense routine. During normal operation,
ALERT idles high. If a fault condition is detected,
ALERT pulls the line low. ALERT remains low until
MODE1 is toggled from high to low.
Click-and-Pop Suppression
In conventional single-supply audio amplifiers, the out-
put-coupling capacitor is a major contributor of audible
clicks and pops. Upon startup, the amplifier charges
the coupling capacitor to its bias voltage, typically half
the supply. Likewise, during shutdown, the capacitor is
discharged to GND. A DC shift across the capacitor
results, which in turn appears as an audible transient at
the speaker. Since the MAX9720 does not require out-
put-coupling capacitors, no audible transient occurs.
Additionally, the MAX9720 features extensive click-and-
pop suppression that eliminates any audible transient
sources internal to the device. The Power-Up/Down
Waveform in the Typical Operating Characteristics
shows that there are minimal spectral components in
the audible range at the output upon startup and shut-
down.
In most applications, the preamplifier output driving the
MAX9720 has a DC bias of typically half the supply.
During startup, the input-coupling capacitor is charged
to the preamplifier’s DC bias voltage through the input
resistor of the MAX9720, resulting in a DC shift across
the capacitor and an audible click/pop. Delaying the
startup of the MAX9720 by 4 to 5 time constants (80ms
to 100ms) based on RIN and CIN, relative to the startup
of the preamplifier, eliminates this click/pop caused by
the input filter.
If the SmartSense routine occurs during normal opera-
tion, a low-level audible transient may be heard. To pre-
vent this, a host-controlled SmartSense routine should
only be executed when ALERT asserts.
50mW, DirectDrive, Stereo Headphone
Amplifier with SmartSense and Shutdown
14
______________________________________________________________________________________
TIP
(SIGNAL)
SLEEVE
(GND)
Figure 6. Typical 2-Wire (Mono) Headphone Plug
OUTR
OUTL
16
14
15
MAX9720
VDD
HPS
R1
100k
Figure 7. HPS Configuration
相关PDF资料 |
PDF描述 |
|---|---|
| MAX97220DETE+ | IC AUDIO AMP HEADPHONE 16TQFN |
| MAX9722AETE+G | IC AMP AUDIO .13W STER AB 16TQFN |
| MAX9723CETE+ | IC AMP AUDIO .06W STER AB 16TQFN |
| MAX9724AEUD+ | IC AMP AUDIO .045W STER 14TSSOP |
| MAX9724DETC+ | IC AMP AUDIO .063W STER 12TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9720BEBE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9720BEBE+ | 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH 2CH STEREO 0.05W CLS-AB 16UCSP - Rail/Tube |
| MAX9720BEBE+T | 功能描述:音频放大器 50mW DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9720BEBE-T | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9720BEUE | 制造商:Maxim Integrated Products 功能描述:50MW, DIRECTDRIVE, STEREO HEADPHONE AMPLIFIER - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。