- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9776ETJ+T (Maxim Integrated Products)IC AMP AUDIO PWR 1.5W D 32TQFN PDF资料下载
参数资料
| 型号： | MAX9776ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/38页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 1.5W D 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | DirectDrive® |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道），带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 1.5W x 1 @ 4 欧姆; 60mW x 2 @ 16 欧姆 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 特点： | 消除爆音，差分输入，I²C，静音，短路和热保护，关机，音量控制 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 配用： | MAX9776EVKIT+-ND - EVALUATION KIT FOR MAX9776 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
MAX9775/MAX9776
2 x 1.5W, Stereo Class D Audio Subsystem
with DirectDrive Headphone Amplifier
22
______________________________________________________________________________________
Filterless Modulation/Common-Mode Idle
The MAX9775/MAX9776 use Maxim’s unique modula-
tion scheme that eliminates the LC filter required by tra-
ditional Class D amplifiers, improving efficiency,
reducing component count, conserving board space
and system cost. Conventional Class D amplifiers out-
put a 50% duty-cycle square wave when no signal is
present. With no filter, the square wave appears across
the load as a DC voltage, resulting in finite load current,
increasing power consumption, especially when idling.
When no signal is present at the input of the
MAX9775/MAX9776, the outputs switch as shown in
Figure 4. Because the MAX9775/MAX9776 drive the
speaker differentially, the two outputs cancel each
other, resulting in no net idle mode voltage across the
speaker, minimizing power consumption.
DirectDrive
Traditional single-supply headphone amplifiers have
outputs biased at a nominal DC voltage (typically half
the supply) for maximum dynamic range. Large cou-
pling capacitors are needed to block this DC bias from
the headphone. Without these capacitors, a significant
amount of DC current flows to the headphone, resulting
in unnecessary power dissipation and possible dam-
age to both headphone and headphone amplifier.
Maxim’s DirectDrive architecture uses a charge pump to
create an internal negative supply voltage. This allows the
headphone outputs of the MAX9775/MAX9776 to be
biased at GND, almost doubling dynamic range while
operating from a single supply. With no DC component,
there is no need for the large DC-blocking capacitors.
Instead of two large (220F, typ) tantalum capacitors, the
MAX9775/MAX9776 charge pump requires two small
ceramic capacitors, conserving board space, reducing
cost, and improving the frequency response of the head-
phone amplifier. See the Output Power vs. Load
Resistance and Charge-Pump Capacitor Size graph in
the
Typical Operating Characteristics for details of the
possible capacitor sizes. There is a low DC voltage on
the amplifier outputs due to amplifier offset. However, the
offset of the MAX9775/MAX9776 is typically 1.4mV,
which, when combined with a 32Ω load, results in less
than 44nA of DC current flow to the headphones.
In addition to the cost and size disadvantages of the
DC-blocking capacitors required by conventional head-
phone amplifiers, these capacitors limit the amplifier’s
low-frequency response and can distort the audio sig-
nal. Previous attempts at eliminating the output-cou-
pling capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raises some issues:
1) The sleeve is typically grounded to the chassis.
Using the midrail biasing approach, the sleeve must
be isolated from system ground, complicating prod-
uct design.
2) During an ESD strike, the driver’s ESD structures are
the only path to system ground. Thus, the amplifier
must be able to withstand the full ESD strike.
3) When using the headphone jack as a lineout to
other equipment, the bias voltage on the sleeve may
conflict with the ground potential from other equip-
ment, resulting in possible damage to the amplifiers.
VIN = 0V
OUT-
OUT+
VOUT+ - VOUT- = 0V
Figure 4. Outputs with No Input Signal
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9778ETI+ | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MAX9779ETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MAX977EEE+ | IC COMPARATOR DUAL 16-QSOP |
| MAX9787ETI+T | IC AMP AUDIO PWR 2.2W AB 28TQFN |
| MAX9788ETI+T | IC AMP AUDIO PWR 2.4W G 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9776EVKIT+ | 功能描述:音频 IC 开发工具 MAX9776 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9777ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9777ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9778ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9778ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。