- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9778ETI+ (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF资料下载
参数资料
| 型号： | MAX9778ETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/27页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 标准包装： | 60 |
| 类型： | AB 类 |
| 输出类型： | 2-通道（立体声）带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 2.6W x 2 @ 4 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，输入多路复用器，静音，关机，热保护， |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
20
_
__
_
BIAS Capacitor
BIAS is the output of the internally generated 2.5VDC
bias voltage. The BIAS bypass capacitor, CBIAS,
improves PSRR and THD+N by reducing power supply
and other noise sources at the common-mode bias
node, and also generates the clickless/popless, start-
up/shutdown DC bias waveforms for the speaker ampli-
fiers. Bypass BIAS with a 1F capacitor to GND.
Supply Bypassing
Proper power-supply bypassing ensures low-noise, low-
distortion performance. Place a 0.1F ceramic capacitor
from VDD to GND. Add additional bulk capacitance as
required by the application, typically 100F. Bypass
PVDD with a 100F capacitor to GND. Locate bypass
capacitors as close to the device as possible.
Gain Select
The MAX9777/MAX9778 feature multiple gain settings on
each channel, making available different gain and feed-
back configurations. The gain-setting resistor (RF) is con-
nected between the amplifier output (OUT_+) and the
gain set point (GAIN_). An internal multiplexer switches
between the different feedback resistors depending on
the status of the gain control input. The stereo
MAX9777/MAX9778 feature two gain options per chan-
nel. See Tables 1a and 1b for the gain-setting options.
Bass Boost Circuit
Headphones typically have a poor low-frequency
response due to speaker and enclosure size limitations.
A bass boost circuit compensates the poor low-frequen-
cy response (Figure 10). At low frequencies, the capaci-
tor CF is an open circuit, and the effective impedance in
the feedback loop (RF(EFF)) is RF(EFF) = RF1.
At the frequency:
where the impedance, CF, begins to decrease, and at
high frequencies, the CF is a short circuit. Here the
impedance of the feedback loop is:
Assuming RF1 = RF2, then RF(EFF) at low frequencies is
twice that of RF(EFF) at high frequencies (Figure 11).
Thus, the amplifier has more gain at lower frequencies,
boosting the system’s bass response. Set the gain roll-
off frequency based upon the response of the speaker
and enclosure.
To minimize distortion at low frequencies, use capaci-
tors with low-voltage coefficient dielectrics when select-
ing CF. Film or C0G dielectric capacitors are good
choices for CF. Capacitors with high-voltage coeffi-
cients, such as ceramics (non-C0G dielectrics), can
result in increased distortion at low frequencies.
Layout and Grounding
Good PC board layout is essential for optimizing perfor-
mance. Use large traces for the power-supply inputs
and amplifier outputs to minimize losses due to para-
sitic trace resistance, as well as route heat away from
the device. Good grounding improves audio perfor-
mance, minimizes crosstalk between channels, and
prevents any digital switching noise from coupling into
the audio signal. If digital signal lines must cross over
or under audio signal lines, ensure that they cross per-
pendicular to each other.
The MAX9777/MAX9778 TQFN package features an
exposed thermal pad. This pad lowers the package’s
thermal resistance by providing a direct heat conduc-
tion path from the die to the PC board. Connect the pad
to signal ground (0V) by using a large pad or multiple
vias to the ground plane.
R
RR
F EFF
FF
() =
×
+
12
1
2
πRC
FF
VBIAS
RIN
RF2
RF1
CF
Figure 10. Bass Boost Circuit
RF1
RF1 RF2
RIN
2
π RF2 CF
1
FREQUENCY
GAIN
Figure 11. Bass Boost Response
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9779ETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MAX977EEE+ | IC COMPARATOR DUAL 16-QSOP |
| MAX9787ETI+T | IC AMP AUDIO PWR 2.2W AB 28TQFN |
| MAX9788ETI+T | IC AMP AUDIO PWR 2.4W G 28TQFN |
| MAX9789CETJ+ | IC AMP AUDIO 2W STER AB 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9778ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9778ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX977EEE | 功能描述:校验器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。