参数资料
型号: MAX9778ETI+
厂商: Maxim Integrated Products
文件页数: 6/27页
文件大小: 0K
描述: IC AMP AUDIO PWR 2.6W AB 28TQFN
标准包装: 60
类型: AB 类
输出类型: 2-通道(立体声)带立体声耳机
在某负载时最大输出功率 x 通道数量: 2.6W x 2 @ 4 欧姆; 200mW x 2 @ 16 欧姆
电源电压: 4.5 V ~ 5.5 V
特点: 消除爆音,输入多路复用器,静音,关机,热保护,
安装类型: 表面贴装
供应商设备封装: 28-TQFN-EP(5x5)
封装/外壳: 28-WFQFN 裸露焊盘
包装: 管件
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
14
_
__
_
Digital Interface
The MAX9777 features an I2C/SMBus-compatible 2-
wire serial interface consisting of a serial data line
(SDA) and a serial clock line (SCL). SDA and SCL facili-
tate bidirectional communication between the
MAX9777 and the master at clock rates up to 400kHz.
Figure 3 shows the 2-wire interface timing diagram. The
MAX9777 is a transmit/receive slave-only device, rely-
ing upon a master to generate a clock signal. The mas-
ter (typically a microcontroller) initiates data transfer on
the bus and generates SCL to permit that transfer.
A master device communicates to the MAX9777 by
transmitting the proper address followed by a com-
mand and/or data words. Each transmit sequence is
framed by a START (S) or REPEATED START (Sr) con-
dition and a STOP (P) condition. Each word transmitted
over the bus is 8 bits long and is always followed by an
acknowledge clock pulse.
SDA and SCL are open-drain outputs requiring a pullup
resistor (500
or greater) to generate a logic-high volt-
age. Series resistors in line with SDA and SCL are option-
al. These series resistors protect the input stages of the
devices from high-voltage spikes on the bus lines, and
minimize crosstalk and undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see the
START
and STOP Conditions section). SDA and SCL idle high
when the I2C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA while SCL is high
(Figure 4). A START condition from the master signals
the beginning of a transmission to the MAX9777. The
master terminates transmission by issuing the STOP
condition; this frees the bus. If a REPEATED START
condition is generated instead of a STOP condition, the
bus remains active.
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START
CONDITION
START
CONDITION
tHD, STA
tSP
tBUF
tSU, STO
tLOW
tSU, DAT
tHD, DAT
tHIGH
tR
tF
Figure 3. 2-Wire Serial-Interface Timing Diagram
SCL
SDA
SSr
P
Figure 4. START/STOP Conditions
SMBus is a trademark of Intel Corp.
相关PDF资料
PDF描述
MAX9779ETI+T IC AMP AUDIO PWR 2.6W AB 28TQFN
MAX977EEE+ IC COMPARATOR DUAL 16-QSOP
MAX9787ETI+T IC AMP AUDIO PWR 2.2W AB 28TQFN
MAX9788ETI+T IC AMP AUDIO PWR 2.4W G 28TQFN
MAX9789CETJ+ IC AMP AUDIO 2W STER AB 32TQFN
相关代理商/技术参数
参数描述
MAX9778ETI+ 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
MAX9778ETI+T 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
MAX9779ETI+ 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
MAX9779ETI+T 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
MAX977EEE 功能描述:校验器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压(最大值):6 mV 电源电流(最大值):1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel