- 您现在的位置：买卖IC网 > PDF目录2092 > MAX9796EBX+TG45 (Maxim Integrated Products)IC AMP AUDIO 2.3W MONO D 36UCSP PDF资料下载
参数资料
| 型号： | MAX9796EBX+TG45 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO 2.3W MONO D 36UCSP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | DirectDrive® |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道），带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 2.3W x 1 @ 4 欧姆 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 特点： | 消除爆音，差分输入，I²C，静音，短路和热保护，关机，音量控制 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 36-UCSP |
| 封装/外壳： | 36-WFBGA，CSBGA |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MAX9796
Early STOP Conditions
The MAX9796 recognizes a STOP condition at any point
during data transmission except if the STOP condition
occurs in the same high pulse as a START condition.
Slave Address
The MAX9796 is available with one preset slave
address (see Table 1). The address is defined as the
seven most significant bits (MSBs) followed by the
read/write (R/W) bit. The address is the first byte of
information sent to the MAX9796 after the START condi-
tion. The MAX9796 is a slave device only capable of
being written to. The R/W bit should be a zero when
configuring the MAX9796.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9796 uses to handshake receipt of each byte of
data (see Figure 9). The MAX9796 pulls down SDA dur-
ing the master-generated 9th clock pulse. Monitoring
ACK allows for detection of unsuccessful data transfers.
An unsuccessful data transfer occurs if a receiving
device is busy or if a system fault has occurred. In the
event of an unsuccessful data transfer, the bus master
may reattempt communications.
Write Data Format
A write to the MAX9796 includes transmission of a
START condition, the slave address with the R/W bit set
to 0 (Table 1), one byte of data to configure the
Command Register, and a STOP condition. Figure 10
illustrates the proper format for one frame.
The MAX9796 only accepts write data, but it acknowl-
edges the receipt of the address byte with the R/W bit
set high. The MAX9796 does not write to the SDA bus
in the event that the R/W bit is set high. Subsequently,
the master reads all 1’s from the MAX9796. Always set
the R/W bit to zero to avoid this situation.
Programming the MAX9796
The MAX9796 is programmed through six control regis-
ters. Each register is addressed by the three MSBs
(B5–B7) followed by five configure bits (B0–B4) as
shown in Table 2. Correct programming of the MAX9796
requires writing to all six control registers. Upon power-
on, their default settings are as listed in Table 3.
2.3W, High-Power Class D Audio Subsystem
with DirectDrive Headphone Amplifiers
20
______________________________________________________________________________________
1
SCL
START
CONDITION
SDA
28
9
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
SLAVE ADDRESS
A6
A5
A4
A3
A2
A1
A0
R/
W
100
11010
Figure 9. Acknowledge
S
ACK
0
ACKNOWLEDGE FROM MAX9796
R/W
ACKNOWLEDGE
FROM MAX9796
B7 B6 B5 B4 B3 B2
COMMAND BYTE IS STORED ON
RECEIPT OF STOP CONDITION
ACK
P
B1 B0
SLAVE ADDRESS
COMMAND BYTE
Figure 10. Write Data Format Example
Table 1. MAX9796 Address Map
B7
B6
B5
B4
B3
B2
B1
B0
FUNCTION
COMMAND
DATA
Input Mode Control
0
INA+20dB
INMODE (Tables 5a and 5b)
Mono Volume Control
0
1
MVOL (Table 7)
Left Volume Control
0
1
0
LVOL (Table 7)
Right Volume Control
0
1
RVOL (Table 7)
Output Mode Control
1
0
MONO+6dB
OUTMODE (Table 9)
Global Control Register
1
0
1
SHDN
IN+6dB
MUTE
SSM
MONO
Table 2. Control Registers
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9813LEKA+T | IC AMP AUDIO MONO AB MIC SOT23-8 |
| MAX9814ETD+T | IC AMP AUDIO MONO AB MIC 14TDFN |
| MAX9820ETB+T | IC AMP AUD HDPHE 95MW 10TDFN |
| MAX98300SETA+T | IC AMP AUD SPKR 2W MONO D 8TDFN |
| MAX98302ETD+ | IC AMP STER CLASS D 2.4W 14TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9796EVKIT | 制造商:Maxim Integrated Products 功能描述:2.3W HIGH-POWER CLASS D AUDIO SUBS - Rail/Tube |
| MAX9796EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX9796 EVAL KIT - Boxed Product (Development Kits) |
| MAX98088EVKIT# | 功能描述:音频 IC 开发工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX98088EVKIT+ | 功能描述:音频 IC 开发工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX98088EWY+T | 功能描述:接口—CODEC Dual I2S Codec RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。