- 您现在的位置：买卖IC网 > PDF目录2092 > MAX9796EBX+TG45 (Maxim Integrated Products)IC AMP AUDIO 2.3W MONO D 36UCSP PDF资料下载
参数资料
| 型号： | MAX9796EBX+TG45 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO 2.3W MONO D 36UCSP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | DirectDrive® |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道），带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 2.3W x 1 @ 4 欧姆 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 特点： | 消除爆音，差分输入，I²C，静音，短路和热保护，关机，音量控制 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 36-UCSP |
| 封装/外壳： | 36-WFBGA，CSBGA |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
due to amplifier offset. However, the offset of the
MAX9796 is typically 1.4mV, which, when combined
with a 32Ω load, results in less than 44nA of DC current
flow to the headphones.
In addition to the cost and size disadvantages of the
DC-blocking capacitors required by conventional head-
phone amplifiers, these capacitors limit the amplifier’s
low-frequency response and can distort the audio sig-
nal. Previous attempts at eliminating the output-cou-
pling capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raises some issues:
1) The sleeve is typically grounded to the chassis.
Using the midrail biasing approach, the sleeve must
be isolated from system ground, complicating prod-
uct design.
2) During an ESD strike, the driver’s ESD structures are
the only path to system ground. Thus, the amplifier
must be able to withstand the full ESD strike.
3) When using the headphone jack as a lineout to other
equipment, the bias voltage on the sleeve may con-
flict with the ground potential from other equipment,
resulting in possible damage to the amplifiers.
Charge Pump
The MAX9796 features a low-noise charge pump. The
switching frequency of the charge pump is half the
switching frequency of the Class D amplifier, regard-
less of the operating mode. The nominal switching fre-
quency is well beyond the audio range, and thus does
not interfere with the audio signals, resulting in an SNR
of 93dB. Although not typically required, additional
high-frequency noise attenuation can be achieved by
increasing the size of C2 (see the
Typical Application
Circuit). The charge pump is active in both speaker
and headphone modes.
Signal Path
The audio inputs of the MAX9796 (INA, INB, and INC)
are preamplified and then mixed by the input mixer to
create three internal signals: left (L), right (R), and mono
(M). Tables 5a and 5b show how the inputs are mixed to
create L, R, and M. These signals are then independent-
ly volume adjusted by the L, R, and M volume control
and routed to the output mixer. The output mixer mixes
the internal L, R, and M signals to create a variety of
audio mixes that are output to the headphone, speaker,
and the mono receiver amplifiers. Figure 6 shows the
signal path that the audio signals take.
Signal amplification takes place in three stages. In the
first stage, the inputs (INA, INB, and INC) are preampli-
fied. The amount by which each input is amplified is
determined by the bits INA+20dB (B4 in the Input Mode
Control Register) and IN+6dB (B3 in the Global Control
Register). After preamplification, they are mixed in the
input mixer to create the internal signals L, R and M.
In the second stage of amplification, the internal L, R,
and M signals are independently volume adjusted.
Finally, each output amplifier has its own internal gain.
The speaker, headphone, and mono receiver amplifiers
have fixed gains of 12dB, 3dB and 3dB, respectively.
MAX9796
2.3W, High-Power Class D Audio Subsystem
with DirectDrive Headphone Amplifiers
______________________________________________________________________________________
17
VDD / 2
VDD
GND
+VDD
-VDD
GND
VOUT
CONVENTIONAL DRIVER-BIASING SCHEME
DirectDrive BIASING SCHEME
Figure 5. Traditional Amplifier Output vs. MAX9796 DirectDrive
Output
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9813LEKA+T | IC AMP AUDIO MONO AB MIC SOT23-8 |
| MAX9814ETD+T | IC AMP AUDIO MONO AB MIC 14TDFN |
| MAX9820ETB+T | IC AMP AUD HDPHE 95MW 10TDFN |
| MAX98300SETA+T | IC AMP AUD SPKR 2W MONO D 8TDFN |
| MAX98302ETD+ | IC AMP STER CLASS D 2.4W 14TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9796EVKIT | 制造商:Maxim Integrated Products 功能描述:2.3W HIGH-POWER CLASS D AUDIO SUBS - Rail/Tube |
| MAX9796EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX9796 EVAL KIT - Boxed Product (Development Kits) |
| MAX98088EVKIT# | 功能描述:音频 IC 开发工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX98088EVKIT+ | 功能描述:音频 IC 开发工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX98088EWY+T | 功能描述:接口—CODEC Dual I2S Codec RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。