- 您现在的位置：买卖IC网 > PDF目录296470 > MAX9851EVCMODU (MAXIM INTEGRATED PRODUCTS INC) MAX9851评估板/评估系统 PDF资料下载
参数资料
| 型号： | MAX9851EVCMODU |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 编解码器 |
| 英文描述： | MAX9851评估板/评估系统 |
| 中文描述： | PCM CODEC |
| 文件页数： | 30/73页 |
| 文件大小： | 1357K |
| 代理商： | MAX9851EVCMODU |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
MAX9851/MAX9853
Stereo Audio CODECs with Microphone, DirectDrive
Headphones, Speaker Amplifiers, or Line Outputs
36
______________________________________________________________________________________
Set HRMODE to 100 (register 0x18, bits B2–B0) to
enable standard stereo headphone mode. Set
HRMODE to 110 to configure balanced mono operation
and 101 for single-ended mono operation. When oper-
ating in balanced mode, the right headphone amplifier
is reconfigured as a slave amplifier to create a bridge-
tied load output. In single-ended mono mode, only the
left headphone amplifier is used. Both mono modes
output the sum of the left- and right-channel audio.
Set HRMODE to 111 to disable the headphone amplifi-
er and enable the mono receiver amplifier. The receiver
amplifier outputs a sum of the left and right headphone
signals to provide 100mW to a telephone earpiece
speaker.
The headphone/receiver amplifiers have programmable
gain controlled by HRVOLL and HRVOLR (registers
0x14 and 0x15). The independent gain control offers a
range of +5.5dB to -74dB.
Class D Speaker Amplifiers
(MAX9851 Only)
Set SPMODE to 11 (register 0x18, bits B4 and B3) to
enable the stereo speaker amplifier of the MAX9851.
SPMODE can be optionally set to enable just the left or
the right speaker.
CPCLK (register 0x1A, bit B0) must
be set to 1 to ensure proper Class D amplifier opera-
tion. The Class D amplifier oscillator is derived from
MCLK. MCLK must be enabled for proper Class D
amplifier operation.
The on-board filterless, low-EMI, Class D audio power
amplifier offers Class AB performance with Class D effi-
ciency. The amplifiers are powered directly from the
battery (PVDD) for maximum efficiency and power out-
put. A typical output power of up to 2W per channel
allows powering of internal speakers without the need
for a separate power amplifier IC. The Class D amplifier
has been optimized for efficiency and greatly reduced
EMI. The output gain is adjustable between +13.1dB
and -66.4dB. The gain of the speaker amplifier is con-
trolled with SPVOLL and SPVOLR (registers 0x16 and
0x17, bits B0–B5).
Efficiency
Rather than using a traditional Class AB speaker amplifi-
er, the MAX9851 uses a high-efficiency Class D audio
amplifier to provide speaker outputs. The MAX9851 uses
Maxim’s unique, patented modulation scheme that elimi-
nates the LC filter required by standard Class D ampli-
fiers, improving efficiency, reducing component count,
and conserving board space and system cost.
Conventional Class D amplifiers output a 50% duty-cycle
square wave when no signal is present. With no filter, the
square wave appears across the load as a DC voltage,
resulting in finite load current, increasing power con-
sumption. When no signal is present at the input of the
MAX9851, the outputs switch in-phase at a low duty
cycle. Because the MAX9851 drives the speaker differ-
entially, the two outputs cancel, resulting in no net volt-
age across the speaker, minimizing power consumption.
Filterless Operation
Proprietary active emissions limiting (AEL) output stage
circuitry allows the amplifier to operate at switching fre-
quencies above 1MHz while still providing at least
20dB margin below FCC-radiated emissions limits. Set
CPCLK = 1 (register 0x1A, bit B0) to configure the
Class D amplifier to operate with a 1.1MHz MCLK
derived switching frequency. The MAX9851 does not
require an output filter, instead relying on the inherent
Figure 5. Traditional Amplifier Output vs. MAX9851/MAX9853
DirectDrive Output
VDD
VDD / 2
GND
CONVENTIONAL AMPLIFIER BIASING SCHEME
DirectDrive AMPLIFIER BIASING SCHEME
+VDD
SGND
-VDD
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9934FART+T | SPECIALTY ANALOG CIRCUIT, PBGA6 |
| MAX9950FCCB | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| MAX9966BGCCQ+D | Quad, Low-Power, 500Mbps ATE Driver/Comparator |
| MAXQ2000-QBX | Low-Power LCD Microcontroller |
| MAYK062DG | 6.2 V, 0.2 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9851EVKIT | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9851 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9853ETM+ | 功能描述:接口—CODEC Stereo Audio CODEC w/DirectDrive Amp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9853ETM+T | 功能描述:接口—CODEC Stereo Audio CODEC w/DirectDrive Amp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9853EVCMODU | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9853EVKIT | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。