- 您现在的位置：买卖IC网 > PDF目录10925 > MAX9853ETM+T (Maxim Integrated Products)IC CODEC AUDIO STEREO 48TQFN PDF资料下载
参数资料
| 型号： | MAX9853ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 28/71页 |
| 文件大小： | 0K |
| 描述： | IC CODEC AUDIO STEREO 48TQFN |
| 标准包装： | 2,500 |
| 类型： | 立体声音频 |
| 数据接口： | 串行 |
| 分辨率（位）： | 18 b |
| ADC / DAC 数量： | 2 / 2 |
| 三角积分调变： | 是 |
| S/N 比，标准 ADC / DAC (db)： | 81.5 / 88 |
| 动态范围，标准 ADC / DAC (db)： | 82 / 87.5 |
| 电压 - 电源，模拟： | 2.6 V ~ 3.3 V |
| 电压 - 电源，数字： | 1.7 V ~ 3.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
MAX9851/MAX9853
Stereo Audio CODECs with Microphone, DirectDrive
Headphones, Speaker Amplifiers, or Line Outputs
34
______________________________________________________________________________________
Changing Serial Audio Interface Modes
Set S1SD0 = S1SDI = 0 (register 0x03 and 0x05, bit B6)
before making any mode changes to serial audio inter-
face S1 to ensure proper operation. Similarly, set
S2SD0 = S2SDI = 0 before making any mode changes
to serial audio interface S2. This will disable the serial
interface and ensure that sampling rate and filtering
changes are made properly. Once the desired mode
has been selected through I2C, the interface can be re-
enabled. Failure to observe this procedure can
result in the MAX9851/MAX9853 being placed in an
invalid operational mode, leading to unexpected
results.
Powering On/Off the MAX9851/MAX9853
The MAX9851/MAX9853 power on in low-power shut-
down mode with all signal paths disabled. It is good
practice to configure all I2C registers except S1SDI and
S2SDI (register 0x03 and 0x05, bit B6) before taking
the MAX9851/MAX9853 out of shutdown. This may
include setting initial volume levels, DAC and ADC
modes of operation, stereo or mono operation, and
audio interface settings. The analog section of the
MAX9851/MAX9853 must be fully operational before
the digital circuitry will function. Enable the charge
pump by setting CPEN = 1 (register 0x1A, bit B4).
Once the MAX9851/MAX9853 have been properly con-
figured, set the global shutdown bit, SHDN, to 1 (regis-
ter 0x1A, bit B7). The MAX9851/MAX9853 are fully
operational 70ms after SHDN is set. Finally, if the DACs
are to be used, program S1SDI and S2SDI as desired
to enable DAC soft-start.
Disable the audio outputs before powering down the
MAX9851/MAX9853 by setting HRMODE and SPMODE
(LOMODE) bits (Register 0x18). Ramping the volume to
maximum attenuation is recommended before disabling
the output amplifiers. Disable the headphone and speak-
er (or line outputs) once the audio is fully attenuated. The
headphone and speaker (or line outputs) can be dis-
abled within 50s of attenuation without any audible
clicks or pops. Place the MAX9851/MAX9853 in shut-
down after the outputs are disabled.
Sigma-Delta DAC
Set DACLEN and DACREN to 1 (register 0x1B, bit B7
and B6) to enable the left and right DACs while the
S1SDI and S2SDI bits are cleared and the SLD status
bit is low to ensure click/pop suppression, then enable
S1SDI and S2SDI as desired. The stereo DACs can mix
any combination of the four channels of data from the
S1 left/right and S2 left/right signal sources using the
MIXDAL/R bits (register 0x08). Digital signals from the
two interfaces in the 8kHz to 48kHz sample rate range
are combined regardless of S1 and S2 interfaces
modes, even if asynchronous with respect to each
other or MCLK (in DAC-only mode).
When operating in standard stereo audio mode, the
input data stream from each interface is passed through
separate 8x FIR interpolating filters. When operating in
voice mode, the primary interface makes use of an inter-
polating IIR voiceband filter with an optional highpass
component. When operating in mono mode, or when
serial input data is disabled for a digital audio interface,
the unused digital-signal processing filter paths are dis-
abled to minimize supply-current consumption.
The stereo signals at the left and right DAC may be addi-
tionally filtered in any mode with a programmable high-
pass filter to band limit the audio output and block DC.
Set DHPL and DHPR (register 0x07, bits B3–B0) to 01,
10, or 11 to select one of the three highpass filter cutoff
frequencies as shown in Table 2.
Sigma-Delta ADC
Set ADCLEN and ADCREN to 1 (register 0x1B, bit B5 and
B4) to enable the MAX9851/MAX9853’s stereo ADCs. The
ADCs accept analog signals from the line inputs and the
microphone inputs which can be mixed as described in
the Signal Routing section prior to conversion. For ADC
operation, program the enabled digital audio interface(s)
to operate in master mode so that the sampling clock is
generated within the MAX9851/MAX9853.
The maximum signal that will not clip the ADC input is
2VP-P. If clipping does occur, reduce the microphone
or line input gain as appropriate. Clipping in the digital
circuitry is indicated by CLD (register 0x00, bit B7).
Table 2. DAC Highpass Filter Modes
DHPL/DHPR BIT
SETTINGS
FILTER MODE
00
No filtering
01
55Hz to 91Hz cutoff frequency
10
171Hz to 279Hz cutoff frequency
11
327Hz to 533Hz cutoff frequency
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9853ETM+ | IC CODEC AUDIO STEREO 48TQFN |
| VE-23Y-IV-F1 | CONVERTER MOD DC/DC 3.3V 99W |
| VE-23X-IX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-23X-IX-F3 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-23X-IX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9853EVCMODU | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9853EVKIT | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9856ATL/V+ | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9856ATL/V+T | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9856ETL/V+ | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。