- 您现在的位置：买卖IC网 > PDF目录10925 > MAX9853ETM+T (Maxim Integrated Products)IC CODEC AUDIO STEREO 48TQFN PDF资料下载
参数资料
| 型号： | MAX9853ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/71页 |
| 文件大小： | 0K |
| 描述： | IC CODEC AUDIO STEREO 48TQFN |
| 标准包装： | 2,500 |
| 类型： | 立体声音频 |
| 数据接口： | 串行 |
| 分辨率（位）： | 18 b |
| ADC / DAC 数量： | 2 / 2 |
| 三角积分调变： | 是 |
| S/N 比，标准 ADC / DAC (db)： | 81.5 / 88 |
| 动态范围，标准 ADC / DAC (db)： | 82 / 87.5 |
| 电压 - 电源，模拟： | 2.6 V ~ 3.3 V |
| 电压 - 电源，数字： | 1.7 V ~ 3.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
MAX9851/MAX9853
Stereo Audio CODECs with Microphone, DirectDrive
Headphones, Speaker Amplifiers, or Line Outputs
______________________________________________________________________________________
37
inductance of the speaker coil to filter the high-frequen-
cy PWM components, and the natural filtering of both
the speaker and the human ear to recover the audio
component of the square-wave output. Eliminating the
output filter results in a smaller, less costly, and more
efficient solution. Because the switching frequency of
the MAX9851 output is well beyond the bandwidth of
cell-phone speakers, voice coil movement due to the
square-wave frequency is negligible.
Differential Line Outputs (MAX9853 Only)
The MAX9853 features a pair of differential line outputs
instead of the Class D speaker amplifiers of the
MAX9851. Set LOMODE to 11 (register 0x18, bits B4
and B3) to enable the stereo line outputs of the
MAX9853. The line outputs can be used simultaneously
with the headphone or receiver amplifier for maximum
flexibility in driving an external audio amplifier or other
analog audio IC. The line outputs feature gain
adjustable between +7.1dB and -72.4dB. Program the
gain of the line outputs with LOPGAL and LOPGAR
(registers 0x16 and 0x17, bits B5 to B0).
Shutdown Output and Fault Input
Shutdown output and fault input pins are available for
interfacing with an external speaker amplifier IC. The
open-drain shutdown output can be used to control an
external amplifier through the MAX9853 I2C interface.
The fault logic input has an internal 300k
Ω pullup resis-
tor which can be reported in the I2C status register and
trigger the interrupt output.
Volume Control
The MAX9851/MAX9853 feature volume control ampli-
fiers on the headphone, receiver, speaker (MAX9851
only), and line (MAX9853 only) outputs that can be con-
trolled through the I2C interface. Each output has sepa-
rate volume control amplifiers for left and right in addition
to a mute feature. Set VSEN to 1 (register 0x18, bit B6) to
enable volume change smoothing. Enabling this feature
gives a smooth-sounding gain change by stepping
through all intermediate settings at a 2ms rate per step
when a volume or mute change occurs.
Set ZDEN to 1 (register 0x18, bit B5) to enable the zero-
crossing detection feature. This causes volume and mute
changes to occur only at zero-crossings of the audio
waveform and reduces objectionable clicks or “zipper
noise” that can occur while making volume changes.
Once the part is initialized, the MCLK is not required
during modes where the ADC and DAC are disabled
(for instance, playing line inputs through the head-
phone outputs). However, the part needs MCLK to be
applied for a short period of time (> 1ms) after power-
on to initialize volume control circuitry—this is only once
per power-on.
Microphone Amplifiers
Two microphone interfaces allow the MAX9851/
MAX9853 to accommodate inputs from both an internal
handset microphone and external headset micro-
phones. Both inputs feature 0 to +20dB of gain selec-
table in 1dB increments with an additional 20dB of gain
selectable to increase the range from 0 to +40dB,
accommodating a wide range of microphones.
Set MEXT to 0 (register 0x12, bit B2) to select the inter-
nal microphone input, featuring a differential input to
minimize noise pickup. A low-noise bias voltage
(INTMICBIAS) is available to bias the microphone from
a clean supply. The mono input signal is treated as a
left microphone signal by MAX9851/MAX9853 internal
circuitry. Bypass INTMICBIAS to GND with a 1F
capacitor.
Set MEXT to 1 to select the external microphone input
featuring stereo single-ended inputs with a separate
ground to reduce noise pickup. Connect the external
microphones to EXTMICBIASL and EXTMICBIASR to
provide a bias voltage for the microphones. Set RBIAS to
0 (register 0x12, bit B0) to select an output impedance of
2.2k
Ω for the independent low-noise bias pins.
Alternatively, set RBIAS to 1 to select an output imped-
ance of 470
Ω. A microphone bias voltage of +2.4V, gen-
erated from INTMICBIAS, is used for both resistor
settings. The selectable bias resistors allow extra flexibili-
ty in selecting microphones without requiring external
resistors to bias the microphones. The 470
Ω impedance
can be chosen when using an external RC filter near the
headset jack. The external biases are high impedance
when disabled, even in the presence of an applied volt-
age up to AVDD.
Sidetone
An internally routed sidetone signal is available to allow
analog routing of the left microphone signal. The
sidetone input is the output of the left microphone gain
amplifier. This sidetone signal has an independent gain
adjustment from -32dB to +30dB. The sidetone signal
is available as an input to both the left and right analog
output mixer (see the Signal Routing section).
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9853ETM+ | IC CODEC AUDIO STEREO 48TQFN |
| VE-23Y-IV-F1 | CONVERTER MOD DC/DC 3.3V 99W |
| VE-23X-IX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-23X-IX-F3 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-23X-IX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9853EVCMODU | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9853EVKIT | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9856ATL/V+ | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9856ATL/V+T | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9856ETL/V+ | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。