- 您现在的位置：买卖IC网 > PDF目录2092 > MAX9877EWP+TG45 (Maxim Integrated Products)IC AUDIO SUBSYSTEM 20-WLP PDF资料下载
参数资料
| 型号： | MAX9877EWP+TG45 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/30页 |
| 文件大小： | 0K |
| 描述： | IC AUDIO SUBSYSTEM 20-WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | DirectDrive® |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道），带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 825mW x 1 @ 4 欧姆; 53mW x 2 @ 16 欧姆 |
| 电源电压： | 2.7 V ~ 5.25 V |
| 特点： | 消除爆音，I²C，输入多路复用器，短路和热保护，关机，音量控制 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 20-WLP |
| 封装/外壳： | 20-WFBGA，WLBGA |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
MAX9877
Low RF Susceptibility, Mono Audio
Subsystem with DirectDrive Headphone Amplifier
24
______________________________________________________________________________________
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START CONDITION
START
CONDITION
tHD:STA
tSU:STA
tBUF
tSU:STO
tLOW
tSU:DAT
tHD:DAT
tHIGH
tR
tF
Figure 6. 2-Wire Interface Timing Diagram
SCL
SDA
SSr
P
Figure 7. START, STOP, and REPEATED START Conditions
SMBus is a trademark of Intel Corp.
I2C Interface Specification
The MAX9877 features an I2C/SMBus-compatible, 2-
wire serial interface consisting of a serial-data line
(SDA) and a serial-clock line (SCL). SDA and SCL facil-
itate communication between the MAX9877 and the
master at clock rates up to 400kHz. Figure 6 shows the
2-wire interface timing diagram. The master generates
SCL and initiates data transfer on the bus. The master
device writes data to the MAX9877 by transmitting the
proper slave address followed by the register address
and then the data word. Each transmit sequence is
framed by a START (S) or REPEATED START (Sr) con-
dition and a STOP (P) condition. Each word transmitted
to the MAX9877 is 8 bits long and is followed by an
acknowledge clock pulse. A master reading data from
the MAX9877 transmits the proper slave address fol-
lowed by a series of nine SCL pulses. The MAX9877
transmits data on SDA in sync with the master-generat-
ed SCL pulses. The master acknowledges receipt of
each byte of data. Each read sequence is framed by a
START (S) or REPEATED START (Sr) condition, a not
acknowledge, and a STOP (P) condition. SDA operates
as both an input and an open-drain output. A pullup
resistor, typically greater than 500
Ω, is required on
SDA. SCL operates only as an input. A pullup resistor,
typically greater than 500
Ω, is required on SCL if there
are multiple masters on the bus, or if the single master
has an open-drain SCL output. Series resistors in line
with SDA and SCL are optional. Series resistors protect
the digital inputs of the MAX9877 from high voltage
spikes on the bus lines, and minimize crosstalk and
undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the
START and STOP
Conditions section).
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START con-
dition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high (Figure 7). A START
condition from the master signals the beginning of a
transmission to the MAX9877. The master terminates
transmission, and frees the bus, by issuing a STOP con-
dition. The bus remains active if a REPEATED START
condition is generated instead of a STOP condition.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9879ERV+T | IC AUDIO SUBSYSTEM 30-UCSP |
| MAX987EUK-T | IC COMP MICRPWR R-R I/O SOT23-5 |
| MAX9888EWY+T | IC CODEC AUDIO FLEXSOUND 63WLP |
| MAX9890AEBL+T | IC SUPP CLICK-POP 9-UCSP |
| MAX9892ELT+T | IC ELIMINATOR CLICK/POP 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9879ERV+T | 功能描述:音频放大器 Audio Subsystem w/DirectDrive RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9879EVKIT+ | 功能描述:音频放大器 Stereo Class D Audio Subsystem with DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX987ESA | 功能描述:校验器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX987ESA+ | 功能描述:校验器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX987ESA+T | 功能描述:校验器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。