参数资料
| 型号： | MAXQ2000-RAX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/39页 |
| 文件大小： | 0K |
| 描述： | IC MCU 32K FLASH 68-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 30 |
| 系列： | MAXQ® |
| 核心处理器： | RISC |
| 芯体尺寸： | 16-位 |
| 速度： | 20MHz |
| 连通性： | 1 线，SPI，UART/USART |
| 外围设备： | LCD，POR，PWM，WDT |
| 输入/输出数： | 50 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 2K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 2.75 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 68-QFN 裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 703 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
MAXQ2000
Low-Power LCD Microcontroller
____________________________________________________________________
15
On reset, the stack pointer, SP, initializes to the top of
the stack (0Fh). The CALL, PUSH, and interrupt-vector-
ing operations increment SP, then store a value at the
location pointed to by SP. The RET, RETI, POP, and
POPI operations retrieve the value @SP and then
decrement SP.
Utility ROM
The utility ROM is a 4kB block of internal ROM memory
that defaults to a starting address of 8000h. The utility
ROM consists of subroutines that can be called from
application software. These include:
In-system programming (bootstrap loader) over JTAG
or UART interfaces
In-circuit debug routines
Test routines (internal memory tests, memory
loader, etc.)
User-callable routines for in-application flash pro-
gramming and fast table lookup
Following any reset, execution begins in the utility
ROM. The ROM software determines whether the pro-
gram execution should immediately jump to location
0000h, the start of user-application code, or to one of
the special routines mentioned. Routines within the utili-
ty ROM are user-accessible and can be called as sub-
routines by the application software. More information
on the utility ROM contents is contained in the
MAXQ
Family User’s Guide: MAXQ2000 Supplement.
Some applications require protection against unautho-
rized viewing of program code memory. For these
applications, access to in-system programming, in-
application programming, or in-circuit debugging func-
tions is prohibited until a password has been supplied.
The password is defined as the 16 words of physical
program memory at addresses x0010h to x001Fh.
A single password lock (PWL) bit is implemented in the
SC register. When the PWL is set to one (power-on
reset default), the password is required to access the
utility ROM, including in-circuit debug and in-system
programming routines that allow reading or writing of
internal memory. When PWL is cleared to zero, these
utilities are fully accessible without password. The
password is automatically set to all ones following a
mass erase.
Programming
The flash memory of the microcontroller can be pro-
grammed by two different methods: in-system pro-
gramming and in-application programming. Both
methods afford great flexibility in system design as well
as reduce the life-cycle cost of the embedded system.
These features can be password protected to prevent
unauthorized access to code memory.
In-System Programming
An internal bootstrap loader allows the device to be
reloaded over a simple JTAG interface. As a result,
software can be upgraded in-system, eliminating the
need for a costly hardware retrofit when updates are
required. Remote software uploads are possible that
enable physically inaccessible applications to be fre-
quently updated. The interface hardware can be a
JTAG connection to another microcontroller, or a con-
nection to a PC serial port using a serial-to-JTAG con-
verter such as the MAXQJTAG-001, available from
Maxim Integrated Products. If in-system programmabili-
ty is not required, a commercial gang programmer can
be used for mass programming.
Activating the JTAG interface and loading the test
access port (TAP) with the system programming instruc-
tion invokes the bootstrap loader. Setting the SPE bit to
1 during reset through the JTAG interface executes the
bootstrap-loader-mode program that resides in the utility
ROM. When programming is complete, the bootstrap
loader can clear the SPE bit and reset the device, allow-
ing the device to bypass the utility ROM and begin exe-
cution of the application software.
The following bootstrap loader functions are supported:
Load
Dump
CRC
Verify
Erase
Optionally, the bootstrap loader can be invoked by the
application code. In this mode, the application software
would configure the SPE and PSS bits for UART com-
munication, then jump to the start of the utility ROM. In
this way, the bootstrap loader can be accessed through
another UART-enabled peripheral, or a PC serial port
through an RS-232 transceiver such as the MAX232.
Because the bootstrap loader defaults to the JTAG con-
figuration on reset, the UART versus JTAG selection
must be made from the application code. As a result,
bootstrap loader access through the UART is not possi-
ble in an unprogrammed device.
相关PDF资料 |
PDF描述 |
|---|---|
| MAXQ2010-RFX+ | IC MCU 16BIT 64KB FLASH 100-LQFP |
| MAXQ3120-FFN+ | IC MCU 32KB FLASH 80-MQFP |
| MAXQ3210-EMX+ | IC MCU 16BIT LP 24-DIP |
| MAXQ3212-EJX+ | IC MCU 16BIT LP 24-TSSOP |
| MAXQ610X-0000+ | MCU 16BIT W/IR MODULE BARE DIE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAXQ2000-RAX+ | 功能描述:16位微控制器 - MCU Low-Power LCD MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ2000-RAXX | 制造商:Maxim Integrated Products 功能描述:BLOOD GLUCOSE MICRO 68QFN - Rail/Tube |
| MAXQ2000-RBX | 功能描述:16位微控制器 - MCU Low-Power LCD MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ2000-RBX+ | 功能描述:16位微控制器 - MCU Low-Power LCD MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ2000-RBXX | 制造商:Maxim Integrated Products 功能描述:BLOOD GLUCOSE MICRO 56TQFN - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。