- 您现在的位置：买卖IC网 > PDF目录17100 > MAXQ7670EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAXQ7670 PDF资料下载
参数资料
| 型号： | MAXQ7670EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/38页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAXQ7670 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | MAXQ® |
| 类型： | MCU |
| 适用于相关产品： | MAXQ7670 |
| 所含物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
MAXQ7670
Microcontroller with 10-Bit ADC,
PGA, 64KB Flash, and CAN Interface
26
______________________________________________________________________________________
The drive capability of the I/O, when configured for out-
put, depends on the value in the PS0 (pad drive
strength) register and can be set for either 1mA or
2mA. When an I/O is configured as an input, writing to
the PO register enables/disables the pullup/pulldown
resistor. The value in the PRO (pad resistive pull direc-
tion) register sets the enabled resistor at the I/O as
either a pullup to DVDDIO or pulldown to GNDIO.
Refer to the
MAXQ7670 User’s Guide for more detailed
information.
Port Characteristics
The MAXQ7670 includes a bidirectional 7-bit I/O port
(P0) whose features include:
Schmitt trigger input circuitry with software-selectable
high-impedance or weak pullup to DVDDIO or pull-
down to GNDIO
Software-selectable push-pull CMOS output drivers
capable of sinking and sourcing 0.5mA
Falling or rising edge interrupt capability
P0.4, P0.6, and P0.7 I/Os contain an additional special
function, such as a logic input/output for a timer channel
Selectable pad drive strength and resistive pull direction
Refer to the
MAXQ7670 User’s Guide for more details.
Figure 11 illustrates the functional blocks of an I/O.
MAXQ20 Core Architecture
The MAXQ7670’s core is a member of the low-cost,
high-performance, CMOS, fully static, 16-bit MAXQ20
core Cs. The MAXQ7670 is structured on a highly
advanced, accumulator-based, 16-bit RISC architec-
ture. Fetch and execution operations complete in one
cycle without pipelining because the instruction con-
tains both the op code and data. The result is a stream-
lined 1 million instructions-per-second-per-megahertz
(MIPS/MHz) C.
The highly efficient core is supported by a 16-level
hardware stack, enabling fast subroutine calling and
task switching. The internal data pointers manipulate
data quickly and efficiently. Multiple data pointers allow
more than one function to access data memory without
having to save and restore data pointers each time. The
data pointers can automatically increment or decre-
ment following an operation, eliminating the need for
software intervention and increasing application speed.
Instruction Set
The instruction set is composed of fixed-length, 16-bit
instructions that operate on registers and memory loca-
tions. The highly orthogonal instruction set allows arith-
metic and logical operations to use any register along
with the accumulator. Special-function registers (also
called peripheral registers) control the peripherals and
are subdivided into register modules. The modular fam-
ily architecture allows new devices and modules to
reuse code developed for existing products. The archi-
tecture is transport-triggered. This means that writes or
reads from certain register locations can also cause
side effects to occur. These side effects form the basis
for the higher-level op codes defined by the assembler,
such as ADDC, OR, JUMP, etc.
Memory Organization
The MAXQ7670 incorporates the following memory
areas (see Figure 12):
8KB (4K x 16) utility ROM
64KB (32K x 16) of flash memory for program storage
2048 bytes (1024 x 16) of SRAM for storage of tempo-
rary variables
16-level stack memory for storage of program return
addresses and general-purpose use
A 16-bit-wide x 16 deep internal hardware stack pro-
vides storage for program return addresses and gener-
al-purpose use. The MAXQ7670 core implicitly uses the
stack when executing an interrupt service routine (ISR)
and also when running CALL, RET, and RETI instruc-
tions. The stack can also be explicitly used by the
MAXQ7670
VDVDDIO
P
N
PI0._
PO0._
PS0._
PD0._
PULLUP/
PULLDOWN
LOGIC
PR0._
PD0._
PO0._
P0._
Figure 11. Digital I/O Circuitry
相关PDF资料 |
PDF描述 |
|---|---|
| EBC28DRYS | CONN EDGECARD 56POS DIP .100 SLD |
| EBC26DRYI | CONN EDGECARD 52POS DIP .100 SLD |
| SCRH6D28-100 | INDUCTOR SMD 10UH 1.70A 10KHZ |
| EEC43DRTS | CONN EDGECARD 86POS DIP .100 SLD |
| EBC31DRTS | CONN EDGECARD 62POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAXQ7670EVKIT+ | 功能描述:开发板和工具包 - 其他处理器 MAXQ7670 Eval Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MAXQ8913 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit, Mixed-Signal Microcontroller with Op Amps, ADC, and DACs for All-in-One Servo Loop Control |
| MAXQ8913EWG+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit, Mixed-Signal Microcontroller with Op Amps, ADC, and DACs for All-in-One Servo Loop Control |
| MAXQ8913EWG-T&R+ | 制造商:Maxim Integrated Products 功能描述:MAXQ8913 IMAGE STABILIZER WLF T&R - Gel-pak, waffle pack, wafer, diced wafer on film |
| MAXQ8913X-0000+ | 功能描述:16位微控制器 - MCU 16-Bit Mxd Sgnl MCU w/Op Amp ADC & DAC RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。