- 您现在的位置：买卖IC网 > PDF目录45186 > MB89635RP-SH 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 PDF资料下载
参数资料
| 型号： | MB89635RP-SH |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 |
| 封装： | SHRINK, DIP-64 |
| 文件页数： | 128/153页 |
| 文件大小： | 7326K |
| 代理商： | MB89635RP-SH |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页当前第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页
HARDWARE CONFIGURATION
2-53
(4) Description of operation
(a) Timer function
This timer has the following two modes: reload timer and one-shot timer.
(1) Reload timer mode
Each time the counter underflows, the value written at the RLBR is reloaded to continue the decre-
ment ing. When the counter underflows, the interrupt flag UF (bit 2) is set. If the IE bit (bit 5) is set to
1, an interrupt request is output. If the TOE bit (bit 6) is set to 1, the value of the TO bit is reversed
each time the timer underflows.
(2) One-shot timer mode
When an underflow occurs, the timer stops operation. When the counter underflows, the interrupt re
quest flag UF (bit 2) is set. The EN bit (bit 7) is automatically set to 0 to stop counting.
In both modes, counting starts when 1 is written at the EN bit (bit 7), and it stops when 0 is written.
(b) Pulse-width measurement function
(1) Measurement start
Writing 1 at the FC bit (bit 7) and EN bit (bit 7) causes the counter to enter the operation-enable state.
Counting starts when the edge of the measured pulse input is detected under this condition. At the
pulse-width measurement function, decrementing is started from FF
H.
(2) Measurement end and measured value
When measurement is terminated, the counter transfers the measured value to the buffer, sets the
measurement-end flag IR (bit 1) and buffer-full flag BF (bit 0), and then enters the operation-enable
state again. At this time, an interrupt request is output if the IE bit (bit 5) is set to 1. However, if the
previous measured value cannot be read after continuous pulse-width measurement, continue to set
the BF flag to hold the previous measured value. The new measured value is discarded.
(3) Long pulse
If the counter undeflows during measurement, set the UF bit (bit 2) to continue counting. In this case,
an interrupt request is also output if the IE bit (bit 5) is set to 1.
(4) Operation stop
Measurement stops when 0 is written at the EN bit (bit 7).
(5) Calculation of pulse width
The measured value to be transferred to the buffer is the same as that of the counter when measure
ment is terminated. Therefore, the pulse width should be calculated as follows:
Pulse width = [(256 - counter value) + (Number of TO reversed
ψ 256)] ψ 1 cycle width of count clock
pulse
相关PDF资料 |
PDF描述 |
|---|---|
| MB89635RPF | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89PV950CF | 8-BIT, 5 MHz, MICROCONTROLLER, CQFP64 |
| MB89951PFM | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 |
| MB89T623PFM | 8-BIT, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89623RP-SH | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB89636 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89636PF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89636PFM | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89636P-SH | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89636R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。