- 您现在的位置：买卖IC网 > PDF目录80562 > MB89P538-201PMC (FUJITSU LTD) MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MB89P538-201PMC |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PQFP64 |
| 封装： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 9/72页 |
| 文件大小： | 2290K |
| 代理商： | MB89P538-201PMC |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
MB89530A Series
DS07-12547-7E
17
■ HANDLING DEVICES
1.
Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded (to prevent latch-up) . When
CMOS integrated circuit devices are subjected to applied voltages higher than Vcc at input and output pins (other
than medium- and high-withstand voltage pins), or to voltages lower than Vss, as well as when voltages in excess
of rated levels are applied between Vcc and Vss, the phenomenon known as latch-up can occur.
When a latch-up condition occurs, supply current can increase dramatically and may destroy semiconductor
elements. In using semiconductor devices, always take sufficient care to avoid exceeding maximum ratings.
Also when switching power on or off to analog systems, care must be taken that analog power supplies (AVCC,
AVR) and analog input signals do not exceed the level of the digital power supply.
2.
Power Supply Voltage Fluctuations
Even within the warranted operating range of the Vcc supply voltage, sudden changes in supply voltage can
cause abnormal operation. As a measure for stability, it is recommended that the Vcc ripple fluctuation (peak to
peak value) should be kept within 10% of the reference Vcc value on commercial power supply (50 Hz/60 Hz),
and instantaneous voltage fluctuations such as at power-on and shutdown should be kept within a transient
variability limit of 0.1V/ms.
3.
Treatment of Unused Input Pins
If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected
to pull-up or pull-down resistance.
4.
Treatment of N.C. Pins
Any pins marked ’NC’ (not connected) must be left open.
5.
Treatment of Power Supply Pins on Models with Built-in A/D Converter
Even when A/D converters are not in use, pins should be connected so that AVCC
= VCC, and AVSS = AVR = VSS.
6.
Precautions for Use of External Clock
Even when an external clock signal is used, an oscillator stabilization wait period is used after a power-on reset,
or escape from sub clock mode or stop mode.
7.
Execution of Programs on RAM
Debugging of programs executed on RAM cannot be performed even when using the MB89PV530.
8.
Wild Register Functions
Wild registers cannot be debugged with the MB89PV530 and tools. To verify operations, actual in-device testing
on the MB89P538 or MB89F538/F538L is advised.
相关PDF资料 |
PDF描述 |
|---|---|
| MC9S12XF512J0MLM | MICROCONTROLLER, QFP112 |
| MSP430F5418AIPNR | 16-BIT, FLASH, 25 MHz, RISC MICROCONTROLLER, PQFP80 |
| MPC8555EPXAKF | RISC PROCESSOR, PBGA783 |
| MPC8555EVTAQD | RISC PROCESSOR, PBGA783 |
| MPC8572CPXARNB | 32-BIT, 1067 MHz, MICROPROCESSOR, PBGA1023 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB89P538-201P-SH | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Original Microcontroller CMOS |
| MB89P538P-101 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Original Microcontroller CMOS, F-2MC-8L MB89530A Series |
| MB89P538P-201 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Original Microcontroller CMOS |
| MB89P538PF-101 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Original Microcontroller CMOS, F-2MC-8L MB89530A Series |
| MB89P538PF-201 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Original Microcontroller CMOS, F-2MC-8L MB89530A Series |
发布紧急采购，3分钟左右您将得到回复。