- 您现在的位置：买卖IC网 > PDF目录45191 > MB90F362SPMT 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MB90F362SPMT |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
| 封装： | PLASTIC, LQFP-48 |
| 文件页数： | 6/59页 |
| 文件大小： | 623K |
| 代理商： | MB90F362SPMT |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
MB90360 Series
14
4.
Precautions for when not using a sub-clock signal
If you do not connect pins X0A and X1A to an oscillator, use pull-down handling on the X0A pin and leave the
X1A pin open.
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempts to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (VCC/VSS)
If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply
and ground externally.
Connect VCC and VSS to the device from the current supply source at a low impedance.
As a measure against power supply noise, connect a capacitor of about 0.1
F as a bypass capacitor between
VCC and VSS in the vicinity of VCC and VSS pins of the device.
7.
Pull-up/down resistors
The MB90360 Series does not support internal pull-up/down resistors (Port 2 : built-in pull-up resistors) . Use
external components where needed.
8.
Crystal oscillator circuit
Noises around X0 or X1 pin may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and
make sure, to the utmost effort, that lines of oscillation circuit do not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board artwork surrounding X0 and X1 pins with a ground
area for stabilizing the operation.
9.
Turning-on sequence of power supply to A/D converter and analog inputs
Make sure to turn on the A/D converter power supply (AVCC and AVR) and analog inputs (AN0 to AN15) after
turning-on the digital power supply (VCC) .
Turn-off the digital power after turning off the A/D converter power supply and analog inputs. In this case, make
sure that the voltage does not exceed AVRH or AVCC (turning on/off the analog and digital power supplies
simultaneously is acceptable) .
VCC
VSS
MB90360
Series
相关PDF资料 |
PDF描述 |
|---|---|
| MB90F395HPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| MB90F428GAPFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90428GBPF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90428GCPF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90427GCPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F362TESPMCRGE1 | 制造商:FUJI 功能描述:Pb Free |
| MB90F362TESPMCR-GE1 | 制造商:FUJITSU 功能描述:MCU 16BIT 16LX 64K FLASH 48LQFP 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP, Controller Family/Series:F2MC-16LX, Core Si |
| MB90F362TESPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F362TESPMCR-GN9E1 | 功能描述:IC MCU 16BIT 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90360E 零件状态:在售 核心处理器:F2MC-16LX 核心尺寸:16-位 速度:24MHz 连接性:CAN，LIN，UART/USART 外设:DMA，POR，WDT I/O 数:36 程序存储容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:3K x 8 电压 - 电源（Vcc/Vdd）:3 V ~ 5.5 V 数据转换器:A/D 16x8/10b 振荡器类型:外部 工作温度:-40°C ~ 105°C（TA） 标准包装:250 |
| MB90F367TPMCR-GE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。