参数资料
型号: MB90F367TSPMT
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48
封装: PLASTIC, LQFP-48
文件页数: 6/59页
文件大小: 623K
代理商: MB90F367TSPMT
MB90360 Series
14
4.
Precautions for when not using a sub-clock signal
If you do not connect pins X0A and X1A to an oscillator, use pull-down handling on the X0A pin and leave the
X1A pin open.
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempts to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (VCC/VSS)
If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply
and ground externally.
Connect VCC and VSS to the device from the current supply source at a low impedance.
As a measure against power supply noise, connect a capacitor of about 0.1
F as a bypass capacitor between
VCC and VSS in the vicinity of VCC and VSS pins of the device.
7.
Pull-up/down resistors
The MB90360 Series does not support internal pull-up/down resistors (Port 2 : built-in pull-up resistors) . Use
external components where needed.
8.
Crystal oscillator circuit
Noises around X0 or X1 pin may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and
make sure, to the utmost effort, that lines of oscillation circuit do not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board artwork surrounding X0 and X1 pins with a ground
area for stabilizing the operation.
9.
Turning-on sequence of power supply to A/D converter and analog inputs
Make sure to turn on the A/D converter power supply (AVCC and AVR) and analog inputs (AN0 to AN15) after
turning-on the digital power supply (VCC) .
Turn-off the digital power after turning off the A/D converter power supply and analog inputs. In this case, make
sure that the voltage does not exceed AVRH or AVCC (turning on/off the analog and digital power supplies
simultaneously is acceptable) .
VCC
VSS
MB90360
Series
相关PDF资料
PDF描述
MB90367SPMT 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP48
MB90F362TPMT 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48
MB90362PMT 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP48
MB90362TSPMT 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP48
MB90F362SPMT 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48
相关代理商/技术参数
参数描述
MB90F387PMCR-GSE1 制造商:FUJITSU 功能描述:
MB90F387PMT-GSE1 功能描述:IC MCU FLASH 64K ROM 48LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:F²MC MB90385 产品培训模块:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 标准包装:90 系列:AVR® XMEGA 核心处理器:AVR 芯体尺寸:8/16-位 速度:32MHz 连通性:I²C,IrDA,SPI,UART/USART 外围设备:欠压检测/复位,DMA,POR,PWM,WDT 输入/输出数:50 程序存储器容量:192KB(96K x 16) 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 电压 - 电源 (Vcc/Vdd):1.6 V ~ 3.6 V 数据转换器:A/D 16x12b; D/A 2x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:64-TQFP 包装:托盘 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
MB90F387SPMCR-GE1 制造商:FUJITSU 功能描述:
MB90F387SPMCR-G-JNE1 制造商:FUJITSU 功能描述:
MB90F387SPMCRGSE1 制造商:FUJITSU 功能描述:Pb Free