- 您现在的位置：买卖IC网 > PDF目录69022 > MB91F233LPMC1-GE1 (FUJITSU LTD) 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 PDF资料下载
参数资料
| 型号： | MB91F233LPMC1-GE1 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封装： | PLASTIC, LQFP-120 |
| 文件页数： | 13/68页 |
| 文件大小： | 1635K |
| 代理商： | MB91F233LPMC1-GE1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
MB91230 Series
20
DS07–16506–3E
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC or less than VSS is applied to an input or
output pin or if an above-rating voltage is applied between VCC and VSS pins.
A latch-up, if it occurs, significantly increases the power supply current and may cause thermal destruction
of an element. When you use a CMOS IC, be very careful not to exceed the absolute maximum rating.
Treatment of Unused Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a
pull-up or pull-down resistor.
Treatment of Pins at Unusing LCD
Leave COM0 to COM3 pins open.
V0 to V3 pins should always be pulled up or down through resistance of at least 2 k
.
About Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power
supply and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of
strobe signals caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS
near this device.
About Crystal Oscillator Circuit
Noise near the X0, X1, X0A and X1A pins may cause the device to malfunction. Design the printed circuit
board so that X0, X1, X0A and X1A the crystal oscillator (or ceramic oscillator) , and the bypass capacitor
to ground are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0, X1, X0A and X1A pins surrounded
by ground plane because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
Treatment of NC and OPEN Pins
Pins marked as NC and OPEN must be left open-circuit.
About Mode Pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such
that the distance between the mode pins and VCC or VSS is as short as possible and the connection impedance
is low.
相关PDF资料 |
PDF描述 |
|---|---|
| MB91264BPF-G-XXXE1 | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91263BPMC-G-XXXE1 | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91264BPMC-G-XXXE1 | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91264BPF-G-XXX | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91263BPFV-G-XXX | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F233PFF-GE1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F248 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F248PFV-GSE1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F248S | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F248SPFV-GSE1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。