- 您现在的位置：买卖IC网 > PDF目录45193 > MB91F366GB 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 PDF资料下载
参数资料
| 型号： | MB91F366GB |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封装： | PLASTIC, QFP-120 |
| 文件页数： | 25/64页 |
| 文件大小： | 800K |
| 代理商： | MB91F366GB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
FME / EMDC / Br - mb91f365g_f366g_ds.fm
31
9-Jan-02
CHAPTER 3
IO-Map
see appendix A.
The addresses shown in this table for CAN registers are based on the settings for CS7 done in the Boot ROM
CHAPTER 4
Interrupt Vector Table
see appendix B
CHAPTER 5
Power-on-sequence
All VDD pins should be connected to the same potential. The analogue supply voltage (AVCC) must not be turned
on before the digital supply voltage.
Immediately after power on always execute INIT at the INITX pin (input a low level to the INITX pin). Hold this low
level at the INITX pin long enough so that after release of the low level at INITX and the passing of the built in
waiting time stable oscillation of the oscillation circuit is achieved. INITX must be pulled low for at least 8 cycles of
the 4 MHz oscillation clock.
CHAPTER 6
Handling of Unused Input Pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the de-
vice. Therefore they must be tied to VDD or VSS through resistors. In this case those resistors should be more
than 2 KOhm.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
The resistor of more than 2 KOhm is used to limit currents through the protection diodes. In case of voltages at the
unused pin of 0.3 V or more below VSS or 0.3 V or more above VDD currents which could cause latch-up will flow
through those diodes. It is possible to use one resistor to connect several pins to VDD or VSS. Care should be
taken not to connect pins from different supply voltage domains to one resistor.
CHAPTER 7
Emulation Device
MB91FV360GA can be used as an emulation device for MB91F365GB/F366GB/366GA. MB91F365GB/F366GB/
366GA use the following resources of MB91FV360G (see MB91FV360GA IO-Map):
Reload Timer 0 - Reload Timer 5
UART 0 / U-Timer 0 - UART 1 / U-Timer 1
相关PDF资料 |
PDF描述 |
|---|---|
| MB91F368GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F366GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F364GPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F365GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F467DBPVSR-GSE2 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP208 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F366GBPMC3-G | 功能描述:MCU 32-BIT FR50 RISC 512KB FLASH RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91360G 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| MB91F366GBPMT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91F366GBPMT-ES | 制造商:FUJITSU 功能描述: |
| MB91F367GA | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-BIT MICROCONTROLLER |
| MB91F367GB | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
发布紧急采购，3分钟左右您将得到回复。