参数资料
型号: MB95F108AJWPMC-GE1
厂商: Fujitsu Semiconductor America Inc
文件页数: 7/72页
文件大小: 0K
描述: IC MCU 60K FLASH 64-LQFP
标准包装: 1
系列: F²MC MB95100AM
核心处理器: F²MC-8FX
芯体尺寸: 8-位
速度: 16MHz
连通性: I²C,LIN,SIO,UART/USART
外围设备: LVD,POR,PWM,WDT
输入/输出数: 54
程序存储器容量: 60KB(60K x 8)
程序存储器类型: 闪存
RAM 容量: 2K x 8
电压 - 电源 (Vcc/Vdd): 2.4 V ~ 5.5 V
数据转换器: A/D 12x8/10b
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 64-LQFP
包装: 托盘
产品目录页面: 722 (CN2011-ZH PDF)
配用: 865-1104-ND - KIT STARTER 8FX MCU MB95F108AHS
其它名称: 865-1070
MB95100AM Series
DS07-12614-5E
15
■ HANDLING DEVICES
Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AVCC, AVR) and analog input voltage from exceeding
the digital power supply voltage (VCC) when the analog system power supply is turned on or off.
Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the Vcc power-supply voltage.
For stabilization, in principle, keep the variation in Vcc ripple (p-p value) in a commercial frequency range
(50 Hz/60 Hz) not to exceed 10% of the standard Vcc value and suppress the voltage variation so that the
transient variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply
is switched.
Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
Serial communication
There is a possibility to receive wrong data due to noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example apply a checksum and retransmit
the data if an error occurs.
■ PIN CONNECTION
Treatment of Unused Input Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent dam-
age. Unused input pins should always be pulled up or down through resistance of at least 2 k
Ω. Any unused
input/output pins may be set to output mode and left open, or set to input mode and treated the same as unused
input pins. If there is unused output pin, make it to open.
Treatment of Power Supply Pins on A/D Converter
Connect to be AVCC
= VCC and AVSS = AVR = VSS even if the A/D converter is not in use.
Noise riding on the AVCC pin may cause accuracy degradation. So, connect approx. 0.1
μF ceramic capacitor
as a bypass capacitor between AVCC and AVSS pins in the vicinity of this device.
相关PDF资料
PDF描述
MB95F118JWPMC-GE1 IC MCU 60K FLASH 2KB RAM 52LQFP
MB95F128DPMC-GE1 IC MCU FLASH 60K ROM 100LQFP
MB95F128JBPF-GE1 IC MCU 60KB FLASH 100QFP
MB95F136JBWPF-GE1 IC MCU 32KB FLASH 28SOP
MB95F156JJPMC1-GE1 IC MCU FLASH 32K ROM 52LQFP
相关代理商/技术参数
参数描述
MB95F108AMS 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMSPFM 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMSPFV 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMW 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F108AMWPFM 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers