- 您现在的位置：买卖IC网 > PDF目录80499 > MB95F133NWPFV (FUJITSU LTD) 8-BIT, FLASH, 32.5 MHz, MICROCONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | MB95F133NWPFV |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 32.5 MHz, MICROCONTROLLER, PDSO28 |
| 封装： | 8.60 X 17.75 MM, 2.80 MM HEIGHT, 1.27 MM PITCH, PLASTIC, SOP-28 |
| 文件页数： | 22/63页 |
| 文件大小： | 522K |
| 代理商： | MB95F133NWPFV |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
MB95130M Series
29
*1: The parameter is based on AVSS
= VSS = 0.0 V.
*2: Apply equal potential to AVCC and VCC. AVR should not exceed AVCC
+ 0.3 V.
*3: VI and VO should not exceed Vcc + 0.3 V. VI must not exceed the rating voltage. However, if the maximum
current to/from an input is limited by some means with external components, the ICLAMP rating supersedes
the VI rating.
*4: Applicable pins: P10 to P15, PF0, PF1 (Inapplicable pins: PG1, PG2)
Use within recommended operating conditions.
Use at DC voltage (current).
+B signal is an input signal that exceeds VCC voltage. The + B signal should always be applied a limiting
resistance placed between the
+ B signal and the microcontroller.
The value of the limiting resistance should be set so that when the + B signal is applied the input current
to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this affects
other devices.
Note that if the + B signal is inputted when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the + B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the + B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, etc.) cannot accept
+B signal input.
Sample recommended circuits :
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
Vcc
R
Input/Output Equivalent circuits
+ B input (0 V to 16 V)
Limiting
resistance
Protective diode
相关PDF资料 |
PDF描述 |
|---|---|
| MC7448THX1267NC | 32-BIT, 1267 MHz, RISC PROCESSOR, CBGA360 |
| MPC8555PXAPEX | 32-BIT, 833 MHz, RISC PROCESSOR, PBGA783 |
| MPC8560PX833JC | 32-BIT, 833 MHz, RISC PROCESSOR, PBGA783 |
| M906-02-150.0000LF | 150 MHz, OTHER CLOCK GENERATOR, CQCC36 |
| MK3711SLFTR | 16 MHz, OTHER CLOCK GENERATOR, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB95F134JBS | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F134JBSPF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F134JBSPFV | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F134JBSPFV-GE1 | 制造商:FUJITSU 功能描述:MCU 8-BIT 8FX 16K FLASH SSOP30 制造商:FUJITSU 功能描述:MCU, 8-BIT, 8FX, 16K FLASH, SSOP30 |
| MB95F134JBW | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。