参数资料
型号: MB95F136JBWPF-GE1
厂商: Fujitsu Semiconductor America Inc
文件页数: 6/64页
文件大小: 0K
描述: IC MCU 32KB FLASH 28SOP
标准包装: 1
系列: F²MC MB95130MB
核心处理器: F²MC-8FX
芯体尺寸: 8-位
速度: 16MHz
连通性: LIN,SIO,UART/USART
外围设备: LVD,POR,PWM,WDT
输入/输出数: 19
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 1K x 8
电压 - 电源 (Vcc/Vdd): 2.4 V ~ 5.5 V
数据转换器: A/D 8x8/10b
振荡器型: 外部
工作温度: -40°C ~ 105°C
封装/外壳: 28-SOP
包装: 管件
其它名称: 865-1075
MB95130MB Series
14
■ HANDLING DEVICES
Preventing latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when the devices are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if voltage higher than the rating voltage is applied between
VCC pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AVCC) and analog input voltage from exceeding the
digital power supply voltage (VCC) when the analog system power supply is turned on or off.
Stable supply voltage
Supply voltage should be stabilized.
A sudden change in power supply voltage may cause a malfunction even within the guaranteed operating range
of the VCC power supply voltage.
For stabilization, in principle, keep the variation in VCC ripple (p-p value) in a commercial frequency range
(50 / 60 Hz) not to exceed 10
% of the standard VCC value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
Precautions for use of external clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from the sub clock mode or stop mode.
PIN CONNECTION
Treatment of unused pins
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leading to permanent
damage. Unused input pins should always be pulled up or down through resistance of at least 2 k
.
Any unused input/output pins may be set to the output mode and left open, or set to the input mode and treated
the same as unused input pins. If there is any unused output pin, make it open.
Treatment of power supply pins on A/D converter
Connect to be AVCC
= VCC and AVSS = VSS even if the A/D converter is not in use.
Noise riding on the AVCC pin may cause accuracy degradation. So, connect approx. 0.1
F ceramic capacitor
as a bypass capacitor between AVCC and AVSS pins in the vicinity of this device.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, all the pins must be connected to external power
supply and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe
signals caused by the rise in the ground level, and to conform to the total output current rating. Moreover, connect
the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS pins
near this device.
Mode pin (MOD)
Connect the mode pin directly to VCC or VSS pins.
To prevent the device unintentionally entering the test mode due to noise, lay out the printed circuit board so as
to minimize the distance from the mode pins to VCC or VSS pins and to provide a low-impedance connection.
相关PDF资料
PDF描述
MB95F156JJPMC1-GE1 IC MCU FLASH 32K ROM 52LQFP
MB95F168JAPMC-GE1 IC MCU FLASH 60K ROM 64LQFP
MB95F204KP-G-SH-SNE2 IC MCU 16KB FLASH F2MC8FX 24SDIP
MB95F223KPH-G-SNE2 IC MCU 8KB FLASH F2MC-8FX 16DIP
MB95F263KPF-G-SNE2 IC MCU 8BIT 12KB FLASH 20SOP
相关代理商/技术参数
参数描述
MB95F136JBWPFV 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers
MB95F136JS 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F136JSPFV-GE1 制造商:FUJITSU 功能描述:8BIT MCU 32K FLASH 1K RAM SOP28
MB95F136JW 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F136KSPF-GE1 制造商:FUJITSU 功能描述: