- 您现在的位置：买卖IC网 > PDF目录80527 > MB95F572KPF-G-JNE2 (FUJITSU LTD) MICROCONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | MB95F572KPF-G-JNE2 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PDSO8 |
| 封装： | 5.30 X 5.24 MM, 2.10 MM HEIGHT, 1.27 MM PITCH, PLASTIC, M08, SOP-8 |
| 文件页数： | 38/84页 |
| 文件大小： | 3929K |
| 代理商： | MB95F572KPF-G-JNE2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
MB95560H/570H/580H Series
DS702-00010-1v0-E
43
(Continued)
*1: The parameter is based on VSS = 0.0 V.
*2: VI and VO must not exceed VCC
+ 0.3 V. VI must not exceed the rated voltage. However, if the maximum
current to/from an input is limited by means of an external component, the ICLAMP rating is used instead of
the VI rating.
*3: Applicable to the following pins: P00 to P07, P62 to P64, PF0, PF1, PG1, PG2 (P00, and P62 to P64 are
only available on MB95F562H/F562K/F563H/F563K/F564H/F564K. P01, P02, P03, P07, PF0. PF1, PG1
and PG2 are only available on MB95F562H/F562K/F563H/F563K/F564H/F564K/F582H/F582K/F583H/
F583K/F584H/F584K.)
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistor should be set to a value at which the current to be input to the microcontroller
pin when the HV (High Voltage) signal is input is below the standard value, irrespective of whether the
current is transient current or stationary current.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin,
affecting other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit:
*4: P62 and P63 are only available on MB95F562H/F562K/F563H/F563K/F564H/F564K.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相关PDF资料 |
PDF描述 |
|---|---|
| ML610Q411PA-XXXWA | RISC MICROCONTROLLER, UUC95 |
| MC7448VU1267NC | 32-BIT, 1267 MHz, RISC PROCESSOR, CBGA360 |
| MPC8541CVTAPDX | 32-BIT, 1420 MHz, RISC PROCESSOR, CBGA360 |
| MB88152APNF-G-112-JN-EFE1 | 40 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MC3S12XEP100J1MAL | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, QFP112 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB95F636HP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636HPMC-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F636HWQN-ES-SNE1 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636KP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F636KPMC-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
发布紧急采购，3分钟左右您将得到回复。