收藏本站
参数资料
型号： MB9AF315MPMC
元件分类： 微控制器/微处理器
英文描述： 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
封装： 0.50 MM PITCH, PLASTIC, LQFP-80
文件页数： 51/114页
文件大小： 1357K
代理商： MB9AF315MPMC
41
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
11.
System Control and Reset
11.1
Resetting the AVR
During reset, all I/O registers are set to their initial values, and the program starts execution from the reset vector. For Atmel
ATmega168PA the instruction placed at the reset vector must be a JMP – absolute jump – instruction to the reset handling
routine. For the Atmel ATmega48PA and Atmel ATmega88PA, the instruction placed at the reset vector must be an RJMP –
relative jump – instruction to the reset handling routine. If the program never enables an interrupt source, the interrupt
vectors are not used, and regular program code can be placed at these locations. This is also the case if the reset vector is
in the application section while the interrupt vectors are in the boot section or vice versa (Atmel ATmega88PA/168PA only).
The circuit diagram in Figure 11-1 on page 42 shows the reset logic. Table 29-5 on page 272 defines the electrical
parameters of the reset circuitry.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes active. This does not require
any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal reset. This allows the power to
reach a stable level before normal operation starts. The time-out period of the delay counter is defined by the user through
the SUT and CKSEL fuses. The different selections for the delay period are presented in
Section 9.2 “Clock Sources” on page 25.
11.2
Reset Sources
The Atmel ATmega48PA/88PA/168PA has four sources of reset:
●
Power-on reset. The MCU is reset when the supply voltage is below the power-on reset threshold (VPOT).
●
External reset. The MCU is reset when a low level is present on the RESET pin for longer than the minimum pulse
length.
●
Watchdog system reset. The MCU is reset when the watchdog timer period expires and the watchdog system reset
mode is enabled.
●
Brown-out reset. The MCU is reset when the supply voltage VCC is below the brown-out reset threshold (VBOT) and the
brown-out detector is enabled.
相关PDF资料
PDF描述
MSP430G2252IRSA16T 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQCC16
MC68HC11ED0VFN2 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44
MSM65514-JS 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC68
MSM65P513-GS-VK 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP64
MSM65P544-SS 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PDIP64
相关代理商/技术参数
参数描述
MB9AF316MAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
MB9AF316MPMC-G-JNE1 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 80LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 80LQFP, Controller Family/Series:ARM Cortex-M3, Core
MB9AF316NABGL-GE1 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 512KB (512K x 8) FLASH 112-LFBGA (10x10) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，EBI/EMI，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:83 程序存储容量:512KB（512K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 16x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:112-LFBGA 供应商器件封装:112-LFBGA（10x10） 标准包装:198
MB9AF316NAPF-G-JNE1 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 512KB (512K x 8) FLASH 100-PQFP (14x20) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，EBI/EMI，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:83 程序存储容量:512KB（512K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 16x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:100-BQFP 供应商器件封装:100-PQFP（14x20） 标准包装:66
MB9AF316NAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*