- 您现在的位置：买卖IC网 > PDF目录378653 > MBRP20030CTL (MOTOROLA INC) POWERTAPP⑩II SWITCHMODE⑩ Power Rectifirer PDF资料下载
参数资料
| 型号： | MBRP20030CTL |
| 厂商： | MOTOROLA INC |
| 元件分类： | 参考电压二极管 |
| 英文描述： | POWERTAPP⑩II SWITCHMODE⑩ Power Rectifirer |
| 中文描述： | 100 A, 30 V, SILICON, RECTIFIER DIODE |
| 文件页数： | 2/4页 |
| 文件大小： | 82K |
| 代理商： | MBRP20030CTL |
2
Rectifier Device Data
MAXIMUM MECHANICAL RATINGS
Terminal Penetration:
0.235 max
Terminal Torque:
25–40 in–lb max
Mounting Torque —
Outside Holes:
30–40 in–lb max
Mounting Torque —
Center Hole:
8–10 in–lb max
Seating Plane
Flatness
1 mil per in.
(between mounting holes)
POWERTAP MECHANICAL DATA
APPLIES OVER OPERATING TEMPERATURE
Vertical Pull
250 lbs. max
2 in. Lever Pull
50 lbs. max
Note: While the POWERTAP is capable of sustaining these vertical and levered tensions, the intimate contact
Note:
between POWERTAP and heat sink may be lost. This could lead to thermal runaway. The use of very
Note:
flexible leads is recommended for the anode connections. Use of thermal grease is highly recommended.
2
″
MOUNTING PROCEDURE
The POWERTAP package requires special mounting considerations because of the long longitudinal axis of the copper heat
sink. It is important to follow the proper tightening sequence to avoid warping the heat sink, which can reduce thermal contact
between the POWERTAP and heat sink.
2–3 TURNS
2–3 TURNS
2–3 TURNS
POWER
HEAT
TAP
SINK
STEP 2:
Finger tighten the center bolt. The bolt may
catch on the threads of the heat sink so it is im-
portant to make sure the face of the bolt or
washer is in contact with the surface of the
POWERTAP.
2–3 TURNS
FINGER–TIGHT
2–3 TURNS
POWER
HEAT
TAP
SINK
STEP 3:
Tighten each of the end bolts between 5 to 10
in–lb.
POWER
HEAT
TAP
SINK
5–10 IN–LB
FINGER–TIGHT
5–10 IN–LB
STEP 4:
Tighten the center bolt between 8 to 10 in–lb.
5–10 IN–LB
8–10 IN–LB
5–10 IN–LB
POWER
HEAT
TAP
SINK
STEP 5:
Finally, tighten the end bolts between 30 to 40
in–lb.
30–40 IN–LB
8–10 IN–LB
30–40 IN–LB
POWER
HEAT
TAP
SINK
STEP 1:
Locate the POWERTAP on the heat sink and
start mounting bolts into the threads by hand
(2 or 3 turns).
相关PDF资料 |
PDF描述 |
|---|---|
| MBRP20035L | SWITCHMODE⑩ Schottky Power Rectifirer |
| MBRP20035L | 240 AMP SCHOTTKY RECTIFIER |
| MBRP20045CT | SCHOTTKY BARRIER RECTIFIERS 200 AMPERES 45 to 60 VOLTS |
| MBRP30035L | SWITCHMODE⑩ Schottky Power Rectifier(POWERTAP III Package) |
| MBRP30035 | 30 AMP MINIATURE POWER RELAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBRP20030CTLG | 功能描述:肖特基二极管与整流器 200A 30V Low Vf RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| MBRP20035L | 制造商:ON Semiconductor 功能描述:Diode Schottky 35V 200A 2-Pin Powertap-III 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MBRP20045CT | 功能描述:肖特基二极管与整流器 200A 45V RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| MBRP20045CTG | 功能描述:肖特基二极管与整流器 200A 45V RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| MBRP20060 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:SCHOTTKY BARRIER RECTIFIER 200 AMPERES 60 VOLT |
发布紧急采购，3分钟左右您将得到回复。