- 您现在的位置：买卖IC网 > PDF目录369891 > MBRS1100T3 (ON SEMICONDUCTOR) Schottky Power Rectifier PDF资料下载
参数资料
| 型号： | MBRS1100T3 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 参考电压二极管 |
| 英文描述： | Schottky Power Rectifier |
| 中文描述： | 2 A, 100 V, SILICON, RECTIFIER DIODE, DO-214AA |
| 封装： | PLASTIC, CASE 403A-03, SMB, 2 PIN |
| 文件页数： | 3/4页 |
| 文件大小： | 77K |
| 代理商： | MBRS1100T3 |
3
Rectifier Device Data
INFORMATION FOR USING THE SMB SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must be
the correct size to insure proper solder connection interface
between the board and the package. With the correct pad
geometry, the packages will self align when subjected to a
solder reflow process.
mm
inches
0.085
2.159
0.108
2.743
0.089
2.261
MOUNTING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and soldering
should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 5 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相关PDF资料 |
PDF描述 |
|---|---|
| MBRS1100T3 | Schottky Power Rectifier(Surface Mount Power Package) |
| MBRS1100T3 | 1 Amp Schottky Rectifier |
| MBRS1100TR | SCHOTTKY RECTIFIER |
| MBRS140LT3 | Surface Mount Schottky Power Rectifier(SMB Power Mount Power Package) |
| MBRS140LT3 | Surface Mount Schottky Power Rectifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBRS1100T3_07 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Schottky Power Rectifier Surface Mount Power Package |
| MBRS1100T3G | 功能描述:肖特基二极管与整流器 1A 100V RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| MBRS1100T3G | 制造商:ON Semiconductor 功能描述:DIODE, SCHOTTKY, 1A, 100V, SMB |
| MBRS1100T3G-CUT TAPE | 制造商:ON 功能描述:MBRS1100T3G Series 1 A 100 V Schottky Barrier Rectifier - DO-214AA |
| MBRS1100TR | 功能描述:肖特基二极管与整流器 1.0 Amp 100 Volt RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。