参数资料
型号: MC10EP016FAG
厂商: ON Semiconductor
文件页数: 4/15页
文件大小: 0K
描述: IC COUNTER 8BIT SYNC ECL 32LQFP
标准包装: 250
系列: 10EP
逻辑类型: 二进制计数器
方向:
元件数: 1
每个元件的位元数: 8
复位: 异步
计时: 同步
计数速率: 1.4GHz
触发器类型: 正,负
电源电压: 3 V ~ 3.6 V
工作温度: -40°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 32-LQFP
供应商设备封装: 32-LQFP(7x7)
包装: 托盘
其它名称: MC10EP016FAGOS
MC10EP016, MC100EP016
http://onsemi.com
12
Applications Information (continued)
EP01
Q0 to Q7
P0 to P7
CLK
TC
PE
CE
Figure 7. 32-Bit Cascaded EP016 Programmable Divider
LO
CLK
MSB
LSB
EP016
EP01
Q0 to Q7
P0 to P7
EP016
CLK
TC
PE
CE
CLK
TC
PE
CE
CLK
TC
PE
CE
CLK
Figure 7 shows a typical block diagram of a 32-bit divider
chain. Once again to maximize the frequency of operation
EP01 OR gates were used. For lower frequency applications
a slower OR gate could replace the EP01. Note that for a
16-bit divider the OR function feeding the PE (program
enable) input CANNOT be replaced by a wire OR tie as the
TC output of the least significant EP016 must also feed the
CE input of the most significant EP016. If the two TC
outputs were OR tied the cascaded count operation would
not operate properly. Because in the cascaded form the PE
feedback is external and requires external gating, the
maximum frequency of operation will be significantly less
than the same operation in a single device.
Maximizing EP016 Count Frequency
The EP016 device produces 9 fast transitioning
single-ended
outputs, thus VCC noise can become
significant in situations where all of the outputs switch
simultaneously in the same direction. This VCC noise can
negatively impact the maximum frequency of operation of
the device. Since the device does not need to have the Q
outputs terminated to count properly, it is recommended that
if the outputs are not going to be used in the rest of the system
they should be left unterminated. In addition, if only a subset
of the Q outputs are used in the system only those outputs
should be terminated. Not terminating the unused outputs
will not only cut down the VCC noise generated but will also
save in total system power dissipation. Following these
guidelines will allow designers to either be more aggressive
in their designs or provide them with an extra margin to the
published data book specifications.
Figure 8. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D - Termination of ECL Logic Devices.)
Driver
Device
Receiver
Device
QD
Q
D
Zo = 50 W
50
W
50
W
VTT
VTT = VCC - 2.0 V
相关PDF资料
PDF描述
MC100EP32DTG IC DIVIDER DIV X2 ECL CLK 8TSSOP
MC100EL33DG IC DIVIDER DIV X4 ECL DIFF 8SOIC
MC100LVEL32DG IC DIVIDER DIV X2 ECL 3.3V 8SOIC
MC10EL33DG IC DIVIDER DIV X4 ECL DIFF 8SOIC
MC10EL32DG IC DIVIDER DIV X2 ECL DIFF 8SOIC
相关代理商/技术参数
参数描述
MC10EP016FAR2 功能描述:计数器移位寄存器 3.3V/5V ECL 8-Bit RoHS:否 制造商:Texas Instruments 计数器类型: 计数顺序:Serial to Serial/Parallel 电路数量:1 封装 / 箱体:SOIC-20 Wide 逻辑系列: 逻辑类型: 输入线路数量:1 输出类型:Open Drain 传播延迟时间:650 ns 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装:Reel
MC10EP016FAR2G 功能描述:计数器移位寄存器 3.3V/5V ECL 8-Bit Synchronous Binary RoHS:否 制造商:Texas Instruments 计数器类型: 计数顺序:Serial to Serial/Parallel 电路数量:1 封装 / 箱体:SOIC-20 Wide 逻辑系列: 逻辑类型: 输入线路数量:1 输出类型:Open Drain 传播延迟时间:650 ns 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装:Reel
MC10EP01D 功能描述:逻辑门 3.3V/5V ECL 4-Input RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量(输入/输出):2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel
MC10EP01DG 功能描述:逻辑门 3.3V/5V ECL 4-Input OR/NOR RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量(输入/输出):2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel
MC10EP01DR2 功能描述:逻辑门 3.3V/5V ECL 4-Input RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量(输入/输出):2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel