- 您现在的位置：买卖IC网 > PDF目录1850 > MC10XS3435DPNAR2 (Freescale Semiconductor)IC SWITCH HIGH SIDE QUAD 24QFN PDF资料下载
参数资料
| 型号： | MC10XS3435DPNAR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 31/51页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HIGH SIDE QUAD 24QFN |
| 标准包装： | 1,200 |
| 类型： | 高端开关 |
| 输出数： | 4 |
| Rds（开）： | 2 x 10 毫欧，2 x 35 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 5A |
| 输入电压： | 4 V ~ 28 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-PowerQFN |
| 供应商设备封装： | 24-PQFN（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
FUNCTIONAL DEVICE OPERATION
PROTECTION AND DIAGNOSTIC FEATURES
PROTECTION AND DIAGNOSTIC FEATURES
hson signal
PWM
hson signal
PWM
PROTECTIONS
Over-temperature Fault
The 10XS3435 incorporates over-temperature detection
and shutdown circuitry for each output structure.
Two cases need to be considered when the output
temperature is higher than T SD :
? If the output command is ON: the corresponding output
is latched OFF. FS will be also latched to logic [0]. To
delatch the fault and be able to turn ON again the
outputs, the failure condition must disappear and the
autoretry circuitry must be active or the corresponding
output must be commanded OFF and then ON (toggling
fault_control signal of corresponding output) or
V SUPPLY(POR) condition if V DD = 0 .
? If the output command is OFF: FS will go to logic [0] till
the corresponding output temperature will be below
T SD .
For both cases, the fault register OT[0:3] bit into the status
register will be set to [1]. The fault bits will be cleared in the
status register after a SPI read command.
Over-current Fault
The 10XS3435 incorporates output shutdown in order to
protect each output structure against resistive short-circuit
condition. This protection is composed by eight predefined
current levels (time dependent) to fit Xenon-HID manners by
default or, 55 W or 28 W bulb profiles, selectable separately
by Xenon bit and 28 W bits (as illustrated Figure 14 , page
37 ).
In the first turn-on, the lamp filament is cold and the current
will be huge. fault_control signal transition from logic [0] to [1]
or an autoretry define this event. In this case, the over-current
protection will be fitted to inrush current, as shown in
OC[1:0] bits select over-current slope speed and OCHI1
current step can be removed in case of OCHI bit is set to [1].
Over-current thresholds
fault_control
hson
In steady state, the wire harness will be protected by
OCLO2 current level by default. Three other DC over-current
levels are available: OCLO1 or OCLO3 or OCLO4 based on
the state of the OCLO[1,0] bits.
If the load current level ever reaches the over-current
detection level, the corresponding output will latch the output
OFF and FS will be also latched to logic [0]. To delatch the
fault and be able to turn ON again the corresponding output,
the failure condition must disappear and the autoretry
circuitry must be active or the corresponding output must be
commanded OFF and then ON (toggling fault_control signal
of corresponding output) or V SUPPLY(POR) condition if V DD =
0.
The SPI fault report (OC[0:3] bits) is removed after a read
operation.
In Normal mode using internal PWM module, the
10XS3435 incorporates also a coolin g bulb filament
management if OC_mode and Xenon are set to logic [1]. In
this case, the 1 st step of multi-step over-current protection will
depend to the previous OFF duration, as illustrated in
be used in function to the duration of previous OFF state
(toff). The slope of cooling bulb emulator is configurable with
OCOFFCB[1:0] bits.
Depending on toff
depending to toff
Over-current thresholds
Cooling
toff
fault_control
hson
Severe Short-Circuit Fault
The 10XS3435 provides output shutdown in order to
protect each output in case of severe short-circuit during of
the output switching.
If the short-circuit impedance is below R SHORT , the device
will latch the output OFF, FS will go to logic [0] and the fault
register SC[0:3] bit will be set to [1]. To delatch the fault and
be able to turn ON again the outputs, the failure condition
must disappear and the corresponding output must be
commanded OFF and then ON (toggling fault_control signal
of corresponding output) or V SUPPLY(POR) condition if V DD =
0.
The SPI fault report (SC[0:3] bits) is removed after a read
operation.
10XS3435
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
相关PDF资料 |
PDF描述 |
|---|---|
| MC13783JVK5R2 | IC PWR MGT AUD CIRCUIT 247MAPBGA |
| MC1403DG | IC VREF SERIES PREC 2.5V 8-SOICN |
| MC14489BDWR2 | IC DRIVER LED/LAMP 5CH 20-SOIC |
| MC14511BFEL | IC LATCH/DECDR/DRVR 7SEG 16SOEIA |
| MC14513BCPG | IC LATCH/DECODER/DRIVER 18DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC10XS3535DHFK | 功能描述:电源开关 IC - 配电 PENTA Output ESWITCH RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC10XS3535DHFKR2 | 功能描述:电源开关 IC - 配电 PENTA Output ESWITCH RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC10XS3535EHFK | 功能描述:电源开关 IC - 配电 Penta 10/35 mOhm HS Sw RoHS:否 制造商:Freescale Semiconductor 输出端数量: 开启电阻（最大值）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压: 电源电流（最大值）: 最大工作温度: 安装风格: 封装 / 箱体: |
| MC10XS3535EHFKR2 | 功能描述:电源开关 IC - 配电 Penta 10/35 mOhm HS Sw RoHS:否 制造商:Freescale Semiconductor 输出端数量: 开启电阻（最大值）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压: 电源电流（最大值）: 最大工作温度: 安装风格: 封装 / 箱体: |
| MC10XS3535HFK | 功能描述:电源开关 IC - 配电 AUTOLIGHTING ESWITCH RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。