- 您现在的位置：买卖IC网 > PDF目录69024 > MC141556P1 (FREESCALE SEMICONDUCTOR INC) UNIVERSAL SERIAL BUS CONTROLLER, PDIP28 PDF资料下载
参数资料
| 型号： | MC141556P1 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 总线控制器 |
| 英文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PDIP28 |
| 封装： | PLASTIC, DIP-28 |
| 文件页数： | 18/21页 |
| 文件大小： | 160K |
| 代理商： | MC141556P1 |
MC141556
6
MOTOROLA
PIN DESCRIPTION
VDD (Pin 1)
This is the +5V power pin of the chip.
OSC1 (Pin 2), OSC2 (Pin 3)
The OSC1 and OSC2 pins are the connections for the on-
chip oscillator. The crystal frequency is 24MHz . OSC1 may
be driven by an external oscillator if an external crystal circuit
is not used.
VSS (Pin 4)
This is the ground pin of the chip.
IICEN (Pin 5)
This is an input pin which requires the default input state
to determine the IIC Mode of Hub controller. During Power-
On Reset, pulling IICEN high configures MC141556 as a IIC
slave to allow customized parameters programmable. Pull-
ing this pin low disables IIC Mode and adopts default param-
eters. See Table1 Configuration selection for detail.
DP0 (Pin 6)
This is the upstream differential data plus I/O pin of the
Hub.
DM0 (Pin 7)
This is the upstream differential data minus I/O pin of the
Hub.
VDD3CAP (Pin 8)
This pin must connect an external capacitor for the inter-
nal 3.3V regulator which supply transceivers of all USB
ports.
OVR1 (Pin 9)
This is the over-current detection pin of the downstream
port 1. Active low is to indicate overcurrent condition occurs.
In GANG mode, OVR1 is the common detection pin for all
the four downstream ports.
PWRSW1 (Pin 10)
This is an output pin which can be used to switch on/off
the external power regulator for the downstream port 1.
Active high is to switch on the power. In GANG mode,
PWRSW1 is the common output pin for all the four down-
stream ports.
DP1 (Pin 11)
This is the differential data plus I/O pin of the downstream
port 1.
DM1 (Pin 12)
This is the differential data minus I/O pin of the down-
stream port 1.
OVR2 (Pin 13)
This is the over-current detection pin of the downstream
port 2. Active low is to indicate overcurrent condition occurs.
PWRSW2 (Pin 14)
This is an output pin which can be used to switch on/off
the external power regulator for the downstream port 2.
Active high is to switch on the power.
DP2 (Pin 15)
This is the differential data plus I/O pin of the downstream
port 2.
DM2 (Pin 16)
This is the differential data minus I/O pin of the down-
stream port 2.
OVR3 (Pin 17)
This is the over-current detection pin of the downstream
port 3. Active low is to indicate overcurrent condition occurs.
PWRSW3 (Pin 18)
This is an output pin which can be used to switch on/off
the external power regulator for the downstream port 3.
Active high is to switch on the power.
DP3 (Pin 19)
This is the differential data plus I/O pin of the down-
stream port 3.
DM3 (Pin 20)
This is the differential data minus I/O pin of the down-
stream port 3.
OVR4 (Pin 21)
This is the over-current detection pin of the downstream
port 4. Active low is to indicate overcurrent condition oc-
curs.
PWRSW4 (Pin 22)
This is an output pin which can be used to switch on/off
the external power regulator for the downstream port 4.
Active high is to switch on the power.
DP4 (Pin 23)
This is the differential data plus I/O pin of the downstream
port 4.
DM4 (Pin 24)
This is the differential data minus I/O pin of the down-
stream port 4.
OVR5/GANG/SCL (Pin 25)
When IIC Mode: this input pin acts as SCL, which is the
synchronizing clock input from the transmitter for IIC proto-
col. (Detailed description of the programming protocol will be
discussed in the IIC Communication section).
When non-IIC Mode: if self-powered, this input pin acts as
OVR5, which is overcurrent detection of downstream port 5;
active low is to indicate overcurrent occurs. If bus-powered,
this input pin acts as GANG to determine Power Control
Mode; pulling this pin low configures the Hub as Ganged
control, and pulling it high as Individual control.
PWRSW5/SDA (Pin 26)
When IIC Mode: this pin acts as SDA, which is a uni-
directional data line for IIC protocol. (Detailed description of
the programming protocol will be discussed in the IIC Com-
munication section).
When non-IIC Mode: if self-powered, this output pin is to
switch on/off the external power regulator for downstream
port 5; active high is to switch on the power.
相关PDF资料 |
PDF描述 |
|---|---|
| MC141556P1 | UNIVERSAL SERIAL BUS CONTROLLER, PDIP28 |
| MC14536BFL2 | 1 TIMER(S), PROGRAMMABLE TIMER, PDSO16 |
| MC14536BFL1 | 1 TIMER(S), PROGRAMMABLE TIMER, PDSO16 |
| MC146805E2CL | 8-BIT, MICROCONTROLLER, CDIP40 |
| MC146805E2Z | MICROCONTROLLER, CQCC40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC141585DWE | 功能描述:IC LCD MONITOR OSD 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| MC141585DWER2 | 功能描述:IC LCD MONITOR OSD 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| MC14161BCPD | 制造商:Motorola Inc 功能描述: |
| MC14161BD | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC141627FT | 制造商:Panasonic Industrial Company 功能描述:IC |
发布紧急采购，3分钟左右您将得到回复。